background image

Drumulator Owners Manual 

 

 

 

out 

having to stop the segment. To enter 

assign 

mode, press the RECORD button while 

in 

record 

mode. The left-hand display will read 

AS 

(for assign). You are now temporarily out 

of 

record 

mode and can reassign sounds to 

the Drum Play buttons. To continue recording, 
press 

RECORD 

again. 

 
7.  Repeat steps 1 through 6 until you have 

recorded the complete drum part. Note that 
while you can change tempo in 

record 

mode, 

you cannot set levels or accents (even while 
in 

assign mo

de).  

Notes: 

 

When possible assign drum sounds to Drum Play 

buttons in a manner that makes a part easier to play. 
For example; By assigning one drum sound to all four 
buttons ‘drumming’ your fingers sequentially will rapidly 
trigger the drum sound. 
 

 

Sounds recorded during one cycle of a segment are 

not permanent until the next cycle starts This is good to 
know if you make a mistake right at

 

the beginning of 

recording a drum part; simply press 

RUN/STOP

 to stop 

the segment, and start over However if you’re adding a 
few notes at the beginning of a song segment be sure 
to wait for the end of the segment to come around 
before hitting 

STOP

. Or the new notes will not be 

stored 

 

2G Erasing A Specific Drum Sound 

 

When you are in 

segment 

mode and editing a 

segment, you may erase a drum or percussion 
sound wherever it appears in the segment. 
 
1.  To erase a particular drum sound wherever it 

appears in the segment, first assign the drum 
sound to be erased to a Drum Play button 
(unless it is already assigned). 

 
2.  While the Drumulator is 

stopped, 

hold down 

ERASE 

(the

 

right-hand display shows a blinking 

cursor). While holding down 

ERASE, 

tap the 

Drum Play button corresponding to the sound 
you want to erase. The cursor will be replaced 
by two letters confirming the drum sound about 
to be erased: 

 

 

 

If you change your mind about erasing, or 
picked the wrong drum sound by mistake, 
release 

ERASE

 and start over. 

 
3.  While continuing to hold down 

ERASE

, press 

ENTER.

 A short beep will confirm that the drum 

has been erased. 

 
 
 

Notes: 

 

 

When you erase a sound in this mode, you erase 

both the accented and non-accented version of the 
sound, regardless of which version is assigned to 
the Drum Play button. 

 

 

Right-hand Readout 

Drum sound to be erased 

bA BASS 

Sn SNARE 

ri RIM 

Hi HI 

TOM 

Md MID 

TOM 

Lo LO 

TOM 

CL CLAVE 

Cb COWBELL 
CP CLAPS 
Ho 

HI HAT OPEN 

Hc 

HI HAT CLOSED 

rd RIDE 

Summary of Contents for Drumulator




























Reviews: