background image

13

E-flite Leader 480 ARF Assembly Manual

Cowling and Spinner Installation

Required parts

Fuselage assembly  Spinner (optional)

Cowling 

Propeller

#0 Phillips head wood screw (4)

Required Tools and Adhesives

Low-tack tape 

Pin vise

Thin CA 

Phillips screwdriver: #1

Box wrench: 10mm

Hex wrench: 2.5mm

Drill bit: 1/16-inch (1.5mm), 5/64-inch (2mm)

Always balance your propeller. An unbalanced 

propeller can cause vibrations to be transmitted 

into the airframe, which could damage the 

airframe or other components as well as 

produce unwanted flight characteristics.

We recommend using the optional spinner 

to enhance the looks of your model.

  1. Install the propeller on the spinner assembly. Do 

not tighten the propeller nut so the assembly can be 

placed on the motor shaft.

  2. Slide the cowling on the fuselage.

Place a piece of 3/32-inch (2.5mm) thick two-

sided tape (not included) between the cowling 

and spinner backplate to set the spacing. This will 

also hold the cowling in position at the front so 

it can be positioned easily at the rear to match 

the paint lines from the cowl to the fuselage.

  3. Slide the propeller/spinner on the motor shaft. 

Position the cowl so there is a gap of 3/32-inch 

(2mm) between the spinner backplate and cowl.

  4. Use low-tack tape to hold the cowling in 

position for the following step. Make sure the 

propeller can rotate without the backplate rubbing 

against the cowling.

  5. Measure 3/16-inch (5mm) forward of the edge of 

the cowl, and in 3/16-inch (5mm) from the paint lines 

on the cowl. Use a pin vise with a 1/16-inch (1.5mm) 

drill bit to drill four holes through the cowling and 

fuselage side for the cowl mounting screws.

Summary of Contents for Leader 480 ARF

































Reviews: