E-FLITE Diamante 25e ARF Assembly Manual Download Page 4

Page: 4 / 40

E-flite Diamante 5e ARF Assembly Manual

Important Information About Motor

Selection

The Diamante 25e does not include a propeller. We are

recommending the Power 25 or Power 32 outrunner motors.
The motor systems listed will provide you with excellent

aerobatic power for sport and/or artistic aerobatic pilots. All

power systems listed include worry-free outrunner motors.

Lightweight Sport Setup

EFLM4025A

Power 25 BL Outrunner, 870Kv

EFLA1060

60A Pro Brushless ESC w/Switching BEC

THP42003S2PPL

4200mAh 3S2P 11.1V Li-Po, 13GA

APC12080E

Electric Propeller, 12x8E

EFLC3005

Celectra 1- to 3-cell Li-Po Charger

EFLAEC303

EC3 Dev & Batt, Male/Female

This is a sport aerobatic setup with limited precision capabilities.

Recommended High Power

Precision Aerobatic Setup

EFLM4032A

Power 32 BL Outrunner, 770Kv

EFLA1060

60A Pro Brushless ESC w/Switching BEC

THP42004S2PPL

4200mAh 4S2P 14.8V Li-Po, 13GA

APC13065E

Electric Propeller, 13x6.5E

EFLAEC303

EC3 Dev & Batt, Male/Female

This is our recommended setup. Expect high power precision

aerobatics and very strong aggressive artistic aerobatics

performance.

Alternative Sport and

Precision Setup

EFLM4032A

Power 32 BL Outrunner, 770Kv

THP42003S2PPL

4200mAh 3S2P 11.1V Li-Po, 13GA

APC14070E

Electric Propeller, 14x7E

EFLM4025A

Power 25 BL Outrunner, 870Kv

THP42004S2PPL

4200mAh 4S2P 14.8V Li-Po, 13GA

APC12060E

Electric Propeller, 12x6E

And

EFLA1060

60A Pro Brushless ESC w/Switching BEC

EFLAEC303

EC3 Dev & Batt, Male/Female

This is an alternative sport and precision aerobatic setup and

is a good option if you have some equipment and do not

want to purchase additional. Both options are very similar in

performance; you should expect better performance than our

lightweight sport setup and less performance than with our

recommended high power precision setup.

Optional Accessories

EFLA110

Power Meter

HAN172

Hangar 9 Digital Servo and

Rx Current Meter

Note on Lithium Polymer Batteries

Lithium Polymer batteries are significantly more

volatile than alkaline or Ni-Cd/Ni-MH batteries used

in RC applications. All manufacturer’s instructions

and warnings must be followed closely. Mishandling

of Li-Po batteries can result in fire. Always follow the

manufacturer’s instructions when disposing of Lithium

Polymer batteries.

Summary of Contents for Diamante 25e ARF









































Search results

Summary of Contents for Diamante 25e ARF

Reviews:

Related manuals for Diamante 25e ARF

Brands by name

Popular brands

E-FLITE Diamante 25e ARF, Assembly Manual

Search results

Summary of Contents for Diamante 25e ARF

Reviews:

Related manuals for Diamante 25e ARF

Brands by name

Popular brands