background image

EN

1.   Slide the wing tube (

A

) into the fuselage.

CAUTION: 

DO NOT crush or otherwise damage the wiring when 

attaching the wing to the fuselage.

2.   Install the left and right wing (

B and C

) over the wing tube and into the 

wing slot of the fuselage while inserting the aileron servo connectors 
through the provided holes.

3.   Invert the fuselage so the landing gear is facing up. Secure the left and 

right wings to the fuselage using the included screws (

D

).

4.   Remove the screw (

E

) and the receiver cover (

F

) from the bottom of the 

fuselage.

Tip:

 If needed, use hemostats or pliers to pull the servo connectors 

into the fuselage.

5.   Connect the aileron servos from the wings to the Y-harness connectors in 

the fuselage. The left and right aileron servos can be connected to either 
side of the Y-harness.

6.  Replace the receiver cover and the screw.

Disassemble in reverse order.

IMPORTANT:

 Correct operation of the AS3X system requires connection of  

both ailerons to the included Y-harness and the AILE channel of the receiver.

Wing Installation

A

B

C

F

E

Servo Arm Settings

Fly the model at recommended settings before making changes.
The linkages installed at the factory position are chosen for the most
balanced aerobatic response and AS3X performance. Linkage connections
directly affect aircraft response and AS3X performance.

NOTICE:

 Moving a linkage to another position may block the servo arm or

affect AS3X functionality. Refer to the receiver instructions for more information 
about AS3X functionality.

Arms

Elevator

Rudder

Ailerons

D

3 X 18mm (2)

D

10

Summary of Contents for Carbon-Z Yak 54 3X
























Reviews: