manualshive.com logo in svg

E-flight Blade SR RTF Airframe, Instruction Manual

Share
Download
E-flight Blade SR RTF Airframe Instruction Manual Download Page 3

4

5

Blade SR RTF Contents

Item 

Description

Not Available Separately  . . . . . . . . . . . . . . Blade SR RTF Airframe
EFLH1057  . . . . . . . . . . . . . . . . . . . . . . . . HP6DSM 6-Channel Transmitter, 2.4GHz DSM2: BSR
EFLB0997  . . . . . . . . . . . . . . . . . . . . . . . . 1000mAh 3S 11.1V 15C Li-Po, 20AWG JST/Balance
EFLC3105  . . . . . . . . . . . . . . . . . . . . . . . . 3S 11.1V Li-Po Balancing Charger, 0.8A
EFLC4000  . . . . . . . . . . . . . . . . . . . . . . . . AC to 12V DC, 1.5- Amp Power Supply
EFLH1519  . . . . . . . . . . . . . . . . . . . . . . . . Micro Helicopter Main Blade Holder: BSR
EFLH1129  . . . . . . . . . . . . . . . . . . . . . . . . Mounting Accessories & Wrench
EFLH1528  . . . . . . . . . . . . . . . . . . . . . . . . Hook and Loop Material
EFLH1444  . . . . . . . . . . . . . . . . . . . . . . . . Hook and Loop Strap
FUG4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AA Batteries 

Needed to Complete

No additional equipment is required to complete your Blade SR.

Preparing for the First Flight

Please note this checklist is not intended to be a replacement for the content of this instruction manual. Although it can 

be used as a quick start guide, we strongly suggest reading through this manual completely before proceeding.

•  Remove and inspect contents

•  Begin charging the flight battery (see charging procedures on following pages)

•  Install the 4 included AA batteries in the transmitter

•  Install the flight battery in the helicopter (once it has been fully charged)

•  Check the Center of Gravity of the helicopter (see page 12)

•  Test the controls (see page 14)

•  Install the optional Training Gear Set (EFLH1527; strongly recommended if this is your first collective-pitch 

equipped helicopter model)

•  Familiarize yourself with the controls

•  Find a suitable area for flying

Flying Checklist

Please note this checklist is not intended to be a replacement for the content of this instruction manual. Although it can 

be used as a quick start guide, we strongly suggest reading through this manual completely before proceeding.

q

 Always turn the transmitter on first

q

 Plug the flight battery into the 2-in-1 control unit

q

 Allow the 2-in-1 control unit and gyro to arm and initialize properly

q

 Fly the model

q

 Land the model

q

 Unplug the flight battery from the 2-in-1 control unit

q

 Always turn the transmitter off last

Summary of Contents for Blade SR RTF Airframe







































Reviews:

No comments

Brands by name

Popular brands

Load more brands