manualshive.com logo in svg

E+E Elektronik EE772, User Manual

Share
Download
E+E Elektronik EE772 User Manual Download Page 22

22

US-Unit

Analogue output 

[0...10 V / 0(4)...20 mA]

  from 

to  

unit

   

 

 low 

(L1) 

high 

(H1)

 

  

Standardized 

DN40: 

0 

260 520 SCFM

  volumetric 

flow  DN50: 

0 410 

820  

SCFM

   

DN65: 

0  

820 

 

SCFM

   

DN80: 

0  

820 

 

SCFM

  Mass 

flow 

DN40: 

0 570 

1140 

kg/h

   

DN50: 

0 890 

1780 

 

kg/h

   

DN65: 

0  

1780 

 

kg/h

   

DN80: 

0  

1780 

 

kg/h

  Standardized 

flow 

DN40/50

 

0 

19685 

39370  

SFPM

   

DN65 

0  

23081 

SFPM

   

DN80 

0  

15238 

SFPM

  Temperature 

all 

Ø -4 

176 

176 

°F

Switching output  

 

 

 

[switching point/hysteresis]

  

Standardized 

DN40: 

 

210/21 420/42 SCFM

  volumetric 

flow  DN50: 

 330/33 

660/66 

 

SCFM

   

DN65: 

  

660/66 

 

SCFM

   

DN80: 

  

660/66 

 

SCFM

  Mass 

flow 

DN40: 

 460/46 

920/92 

kg/h

   

DN50: 

 700/70 

1400/140 

 

kg/h

   

DN65: 

  

1400/140 

 

kg/h

   

DN80: 

  

1400/140 

 

kg/h

  Standardized flow 

DN40/50

 

 

15000/1500 

30000/3000  

SFPM

   

DN65 

  

15000/1500 

SFPM

   

DN80 

  

10000/1000 

SFPM

  Temperature 

all 

Ø  90/9 

150/15 

°F

Pulse output   

pulse value = 1CF   

pulse duration = 0.1 s

CONFIGURATION SOFTWARE

LIMITED LIABILITY

 

E+E Elektronik shall not be held liable for any damages or consequential damages (for example, but not 

restricted to, loss of earnings, interruption of business, loss of information and data or any other financial 

losses) resulting from the installation, use or impossibility of use of an E+E Elektronik software product and 

any associated support services or non-performance of support services.

1. 

General

The configuration software can be downloaded free of charge at 

www.epluse.com/EE772

The configuration software, allows for a user-friendly adaptation of the flow meter to the application. In addi-

tion, the measurement values for flow and temperature can be calibrated / adjusted.

The system requirements for the installation and execution of the software are:

• 

Windows XP with SP3, Windows Vista or Windows 7

• 

.NET framework 3.5 with SP1

• 

USB 2.0 interface

During setup there will be no installation of .NET Framework 3.5 SP1 – if the required version is not already 

installed on the computer the following error message will appear at the start of the configuration software.

 

.NET Framework 3.5 SP1 can be installed using Windows Update.

Summary of Contents for EE772

































Reviews:

No comments

Brands by name

Popular brands

Load more brands