Dynaudio IP 17 Owners Manual Installation Product Download Page 6

06  

Dynaudio Installation Product

Safety Instructions

Sicherheitshinweise

Bevor Sie mit der Positionierungs-Schablone die Wandaus-

sparungen freilegen, sollten Sie sich unbedingt vergewissern,

dass sich hier 

keine anderen Installationen

wie Rohre oder

Leitungen (Wasser, Gas, elektrischer Strom) befinden.

Im Interesse Ihrer Sicherheit sollten Sie mit einem Metalldetektor

den vorgesehenen Installationsort genau absuchen und so Ge-

fahren oder Schäden vermeiden. Grundsätzlich empfehlen wir

Ihnen die Beratung durch einen Fachmann.

Before producing the wall cut-out using the supplied template,

be sure that 

no conflict with other in-wall installations

will

occur (pipe work, air conditioning, power cabling, etc.).

In existing (retrofit) construction applications, Dynaudio recom-

mends using a stud-finding tool to map the wall construction

accurately, a pipe detector to scan the proposed installation

position and an electrical field detector to help avoid any risk of

electrical damage or shock.

Ideal Surrounding

Einbauhinweise

Die Dynaudio IP Modelle wurden so abgestimmt, dass sie in ver-

schieden großen Wand-Hohlräumen ihr Klangpotenzial entfalten

können. Im Idealfall beträgt das Innenvolumen der Einbauöffnung

für den IP 24 über 30 Liter, für den IP 17 über 15 Liter. 

Der Einbau in Hohlräume mit Luftschächten oder Rohren kann

aufgrund von Vibrationen die Klangqualität mindern.

Aus klanglichen Gründen sollten Sie die Platzierung in Raum-

ecken sowie im Übergangsbereich zu der Decke oder dem Fuß-

boden vermeiden. Wir empfehlen, die Lautsprecher im Abstand

von mindestens 0,5 m zur nächsten Wandecke einzubauen.

Um Bildstörungen durch magnetische Streufelder zu vermeiden,

sollten Sie einen Mindestabstand (0,15 m) zu einem Fernseh-

gerät beachten.

The IP Series models are designed to operate satisfactorily in a

wide range of cavity volumes, for the IP 17 this should ideally be

larger than 0.53 ft

3

(15 liters), while for the IP 24 it would be lar-

ger than 1.1 ft

3

(30 liters). 

Avoid installing the speakers in the same cavity as any ducts, as

this may result in excessive rattle. 

Placement near the intersection of a wall/ceiling, wall/floor or in

a corner is not recommended, as it may detract from the opti-

mum sound quality. If possible, keep the speakers at a distance

greater than 20" (0.5 m) away from any wall edges. 

Due to the residual magnetic field from the drivers, it is advisable

to position the speakers at a minimum distance of 6" (0.15 m)

from CRT televisions to avoid any adverse effect on the picture.

Summary of Contents for IP 17





















Reviews: