background image

Long-Term Care Bed • D500 • 5 Function Ultra Low Bed (Reorder No. 12005)

Long-Term Care Bed • D500 • 5 Function Ultra Low Bed (Reorder No. 12005) 

9

ASSEMBLY INSTRUCTIONS 

(Continued)

2.6  CONNECTING CABLES TO THE 

CONTROL BOX

 

Motor cables will need to be connected to the control 

box, located at the center of the bed.  The motors for 

the backrest control and head section height adjust-

ment should already be connected.

 

1.  Open the control box locking lid by pressing in the 

sides and lift it up, to expose the connection ports.

  

 

2.  The cables and the port connections are color- 

coded. Route the cables to their matching port. 

When running the cables, ensure they are neatly 

tied along the bed frame and do not interfere with 

the bed operation.

  

 

  1. Backup Battery (if applicable)

 

  2. Backrest Motor 1

 

  3. Backrest Motor 2

 

  4. Headboard Motor 

5. Footboard Motor 

6. Knee-break Motor 

7. Underbed Lighting (if applicable) 

8. Nursing Control (if applicable) 

9. Hand pendant

  

1

2

3

4

5

6

7 8

9

 

3.  Connect all cables and reinstate the locking lid, 

ensure there is an audible click.

2.7  INSTALLING BATTERY BACKUP

 

1.  Switch the power supply off when installing the 

backup battery.

 

2.  Affix the backup battery with nuts and bolts to the 

left of the control box, on the same holding plate.

  

 

3.  Open the control box locking lid by pressing in 

the sides and lift it up, to expose the connections 

ports.

 

4.  Connect the backup battery cord to the control 

box. The connection port is indicated with a bat-

tery symbol above.

 

5.  Close the locking lid. There should be an audible 

click. Switch the power supply back on.

ASSEMBLY INSTRUCTIONS 

(Continued)

2.8  INSTALLING THE RAILS OR  

ASSIST BARS

 

1.  Before installing the rails or bars, the bed should 

be in the flat position. 

 

2.  Unclip the metal snap ring and remove the metal 

pins from the rail mounting brackets. 

  

 

3.  Remove cover for the appropriate holes.

  

Holes for 

Swing Rails

Holes for 

Swing Rails

Holes for Assist Bars

 

4.  Place the rail bracket onto the edge of the bed 

decking. Align the rail bracket mounting holes  

with the bed deck mounting holes.

  

 

5.  Re-insert the metal pins from the outside edge of 

the bed through the mounting holes and secure 

with the snap rings on the inside edge of the bed. 

Make sure the snap rings are positioned in the 

groove of the metal pins.

  

 

6.  If the bed rail or bar has additional allen screws, 

tighten the allen screws next to the metal pins. 

 

7.  Repeat the same procedure to install the other rail.

Summary of Contents for 12005










Reviews: