DynaLock 2511 Series Mounting Instructions Download Page 8

Page: 8 / 8

Page 4

2500/2280 WIRING

SERIES 2500 & 2280

ELECTROMAGNETIC LOCK

WIRING INSTRUCTIONS

1/07

Dyna

Lock

705 Emmett Street Bristol, CT 06010

1-877-DynaLock www.dynalock.com

OPERATING VOLTAGES:

12 or 24 VDC/VAC Field Selectable

CURRENT DRAW:

2280

0.68A @ 12VDC / 0.35A @ 24VDC

2500

0.50A @ 12VDC / 0.25A @ 24VDC

(SHOWN

PER

COIL)

SURGE SUPPRESSION:

Built-in

COIL RESISTANCE:

2280

34.1 Ohms (+-10%) Black-White / Red-Blue

2500

53.8 Ohms (+-10%) Black-Black / White-White

GENERAL SPECIFICATIONS

PLEASE DELIVER THIS MANUAL

TO THE END-USER UPON COMPLETION

OF THE INSTALLATION

FOR PRODUCT SUPPORT AND PARTS
ORDERING INFORMATION CONTACT:

DynaLock Corp.
705 Emmett Street
Bristol, CT 06010
Bus: (877) DYNALOCK, Toll-Free USA
(860) 582-4761
Fax: (860) 585-0338

DYNALOCK ON THE INTERNET:

E-mail: [email protected]
Website: www.dynalock.com

Summary of Contents for 2511 Series









Search results

Summary of Contents for 2511 Series

Reviews:

Related manuals for 2511 Series

Brands by name

Popular brands

DynaLock 2511 Series, Mounting Instructions

Search results

Summary of Contents for 2511 Series

Reviews:

Related manuals for 2511 Series

Brands by name

Popular brands