background image

Troubleshooting

Remember: ALWAYS ride within your limits and comfort zone and NEVER 
ride without protective gear!

Issu e 

Problem/C ause 

Solution 

Skateboard does not start up. 

 

Skateboard  controller  is  not 

turned on. 

Turn on. 

 

The  indicator  light  on  the 

charger is red. 

Recharge the skateboard. 

 

No beep heard when turning on 

Signal interference nearby

controller

 

Battery is not properly installed or is 

out of power, re-install or change

 battery.

 

 

Skateboard stops automatically 

after running for some time. 

 

Overheat/overload  protection 

of motor. 

Cool motor. 

 

Low  voltage  production  of 

controller.

 

Signal interference nearby

 

Intermittent power while 

riding.

 

 

 

 

Controller and receiver are wet 

or moist. 

 

Out of power

 

 

Recharge battery. 

 

 

No power can be charged into 

(when the wall outlet in good 

condition), or charger has 

overheated, or charger does not

light up. 

Replace charger. 

 

Red light flashes in succession 

because charger does not work 

smoothly or due to low voltage 

of battery group. 

Change charger or charge the 

battery group. 

Strong vibration and loud 

high-pitched noise when 

running. 

 

Belt is loose or flexible. 

Adjust the belt, fasten screw and 

nut, and readjust nut

 

Bearing is damaged. 

Change bearing. 

Unable to charge skateboard.

 

Drain/dry (may need replacement).

Move away from area with interference.

Move away from area with interference.

-

Change or re charge battery.

The skateboard stops while

              riding

Out of power

Replace drive belt.

Recharge the battery.

Wheels not moving but motor 

still running, the belt is broken.


17

Summary of Contents for 24V eSKATEBOARD

























Reviews: