Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade
®
Abrasive Power Tool.
Warning:
Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important:
All Dynabrade rotary vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Operating Instructions:
Warning:
Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death.
Follow safety procedures posted in workplace.
1.
With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2.
Install air fitting into inlet bushing of tool.
Important:
Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid damaging
valve body housing.
3.
Connect power source to tool. Be careful not to depress throttle lever in the process.
4.
Air tools are not intended for use in explosive atmospheres and are not insulated for contact with electrical power sources. Sanding/Grinding certain materials can create
explosive dust. It is the employers responsibility to notify the user of acceptable dust levels. Sanding/Grinding can cause sparks which can cause fires or explosions.
It is the users responsibility to make sure the work area is free of flammable materials.
Maintenance Instructions:
1.
Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to correct
the cause before use.
2.
Some silencers on air tools may clog with use. Clean and replace as required.
3.
All Dynabrade rotary vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool
specifications state 40 SCFM, set the drip rate of your filter-lubricator at 2 drops per minute). Dynabrade Air Lube (P/N
95842
: 1 pt. 473 ml.) is recommended.
4.
It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due to unclear air, wet
air or insufficient lubrication. Dynabrade recommends the following:
11405
Air Line Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage
filtration of water contaminants and micro-mist lubrication of pneumatic components. Operates 40 SCFM @ 100 PSIG has 3/8" NPT female ports.
5.
Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the
Model #
,
Serial #
, and
RPM
of your machine.
6.
A Motor Tune-Up Kit (P/N
98221
) is available which includes assorted parts to help maintain motor in peak operating condition. Please refer to Dynabrade's Preventative
Maintenance Schedule for a guide to expectant life of component parts.
7.
Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones, chlorinated
hydrocarbons or nitro carbons.
8.
DO NOT clean or maintain air tools with chemicals that have a low flash point (example: WD-40
®
).
9.
Use the 95541 Grease Gun to apply 2 full plunges of the 95542 Grease through the grease fitting that is located in the 56470 Mount Plate Assembly.
Two full plunges of grease should be applied after every 300-hour interval of use.
Full One Year Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date of purchase, all equipment of our
manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or replace at our factory, any equipment or part thereof which shall,
within one year after delivery to the original purchaser, indicate upon our examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance
with factory recommendations, instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect
its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
•
Important:
User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
•
Always disconnect power supply before changing abrasive/accessory or making machine adjustments.
•
Inspect abrasives/accessories for damage or defects prior to installation on tools.
•
Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No.
95903
) for more complete safety information.
Notice
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors can most often be traced to
an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor bearings causing early failure. It often scores the cylinder
walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is contingent upon proper use of our tools and cannot apply to equipment which has been
subjected to misuse such as unclean air, wet air or a lack of lubrication during the use of this tool.
Safety Instructions:
Products offered by Dynabrade should not be converted or otherwise altered
from original design without expressed written consent from Dynabrade, Inc.
Model
Motor
Motor
Pad Dia.
Sound
Maximum Air Flow
Hose I.D. Size
Air Inlet
Weight
Length
Height
Number
HP (W)
RPM
Inch (mm)
Level
CFM/SCFM (LPM)
Inch (mm)
Thread
Pound (kg)
Inch (mm)
Inch (mm)
58441
.45 (336)
900
5 (127)
79 dB(A)
3/23 (651)
1/4 (8)
1/4" NPT
3.6 (1.7)
11-1/16 (281)
5-10/16 (143)
58442
.45 (336)
900
6 (152)
78 dB(A)
3/23 (651)
1/4 (8)
1/4" NPT
3.6 (1.7)
11-1/2 (293)
5-5/8 (141)
58443
.45 (336)
900
6 (152)
79 dB(A)
3/23 (651)
1/4 (8)
1/4" NPT
3.8 (1.7)
11-1/2 (293)
5-5/8 (141)
58444
.45 (336)
900
6 (152)
80 dB(A)
3/23 (651)
1/4 (8)
1/4" NPT
3.8 (1.7)
11-1/2 (293)
5-5/8 (141)
58445
.45 (336)
900
8 (203)
80 dB(A)
3/23 (651)
1/4 (8)
1/4" NPT
3.9 (1.8)
12-1/2 (319)
5-9/16 (142)
58446
.45 (336)
900
8 (203)
81 dB(A)
3/23 (651)
1/4 (8)
1/4" NPT
4.3 (2.0)
12-1/2 (319)
5-9/16 (142)
Additional Specifications: Air Pressure 90 PSIG (6.2 Bar)
Machine Specifications
