manualshive.com logo in svg

dymax PC-3D, Operation Manual, Page: 7 / 21

Share
Download
dymax PC-3D Operation Manual Download Page 7

TM-022 PN 35934 
Rev 05/12/98 

7 

 

PC-3D 

SPECIFICATIONS

 

 

 
 

Voltage: ....................................................... 100 Vac 
 .................................................................... 115 Vac 
 .................................................................... 230 Vac 

Current:  ...................................................... 3 A @ 100 Vac 
 .................................................................... 2.5 A @ 120 Vac 
 .................................................................... 1.5 A @ 220 Vac 

Frequency: .................................................. 50/60 Hz 

Lamp/Reflector: ........................................... 50 Watt DC (pre-focused) 

Shutter Timer: .............................................. 1 to 50 sec. delay 

Dispenser Timer: ......................................... .1 to 3.5 sec. delay 

Air Pressure Requirements: ........................ 100 psi max; clean, dry shop air 

Footswitch: .................................................. DPDT, Rocker type 

Hour-meter: ................................................. 99,999.9 hours, non-resetable 

 

Output Intensities (Typical

 W/cm

2

)** 

 
 

WAVELENGTH               FILTERED              UNFILTERED 

 

      320 - 390 nm                     1.5   

2.5+ 

 

** Measured with an Accu-Cal

®

 20 Radiometer.

 

 
 

CAUTION

 

 

With the filter installed, the PC-3D lamp emits only UV-A light and low amounts of UV-B 

and UV-C ultraviolet light.  Without the filter, UV-A, UV-B, UV-C, and visible light are 

emitted. 

Never

 look directly at the light source while the unit is in use.  

Summary of Contents for PC-3D






















Reviews:

No comments