background image

- 4 -

M965710 Rev. 1.0 (5/17)

9

10

11

ATTACH CABLE CONNECTOR

CHECK OPERATION OF POP-UP

MAKE WATER SUPPLY AND WASTE CONNECTIONS

•  Thread CABLE CONNECTOR

 (1)

 clockwise 

onto DRAIN BODY CONNECTION 

(2)

 and 

hand tighten. 

Fig. A.

Your new POP-UP DRAIN installation is
now complete. 

Fig. B.

Note:  Tailpeice on pop-up drain is  

1-1/4" O.D. (32mm) Fig. B.

•  Operate LIFT KNOB

 (1)

 to verify that STOPPER

 (2)

 opens and closes.

Note:  If STOPPER (2) does not open and close properly then refer to the 

“troubleshooting section” of these instructions.

NOTE:  FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED 

AND MUST BE PURCHASED SEPARATELY.

•  Connect water supply to VALVE BODIES

 (1,1A) 

with 1/2" IPS FLEXIBLE 

SUPPLIES

 (2)

 or 3/8" O.D. BULL-NOSE RISERS

 (3)

. Use 

adjustable wrench to tighten connections. Do not over tighten. 
Be careful not to kink copper supply when bending. Use tubing 
cutter to cut to proper length.

•  Connect HOT water supply to inlet of left SHANK and COLD 

water supply to right SHANK using sealant, appropriate 
connectors, and COUPLING NUTS.

Fig.

 

A.

2

1

1-1/4" O.D.

(32mm)

Fig.

 

A.

Fig.

 

B.

2

HOT

COLD

FERRULE

COMPRESSION

NUT

COUPLING

NUT

FLEXIBLE

SUPPLIES

3/8" (6mm) O.D.

BULL-NOSE

RISERS

1/2" (13mm) PIPE

THREAD

 

 

3/8" (6mm) COMPRESSION

CONNECTION

2

3

1A

1

Summary of Contents for Percy D3510584C









Reviews: