DXV Percy D3510584C Installation Instructions Manual Download

Page: 1 / 8

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017

VE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.

M965710 Rev. 1.0 (5/17)

Cross Handle
Model D3510584C
Lever Handle
Model D3510580C

Percy

Widespread Faucet

ROUGHING-IN DIMENSIONS:

• For reference

Plumbers' Putty or Caulking

Adjustable Wrench

Phillips Screwdriver

Channel Locks

Flat Blade Screwdriver

6" to 12"

(152 to 305 mm)

9-11/16"

(245 mm)

6-9/16"

(167 mm)

5-7/16"

(138 mm)

MOUNTING

SURFACE

2-1/4"

(57 mm)

2-1/4" DIA.

(57 mm)

7/8" DIA.

(22 mm)

1-1/2" MAX.

(38 mm)

CROSS

HANDLE

10-1/2" MAX.

(267 mm)

1-1/4" O.D.

(32 mm)

2" MAX

(51 mm)

1-1/2"

(37 mm)

LEVER

HANDLE

2-1/2"

(63 mm)

NOTE: MOUNTING HOLES ARE 1-3/8" DIA. (35 mm)

CONNECTIONS:

• 1/2" IPS FLEXIBLE SUPPLIES

• 3/8" O.D. BULL-NOSE RISERS

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.

Summary of Contents for Percy D3510584C









Search results

Summary of Contents for Percy D3510584C

Reviews:

Related manuals for Percy D3510584C

Brands by name

Popular brands

DXV Percy D3510584C, Installation Instructions Manual

Search results

Summary of Contents for Percy D3510584C

Reviews:

Related manuals for Percy D3510584C

Brands by name

Popular brands