- 2 -
7302328-100 (3/17)
INSTALL CLOSET BOLTS
Install closet bolts in flange channel,
turn 90°, and slide into place 6"
(152 mm) apart and parallel to wall.
INSTALL TOILET SEAT
Install toilet seat in accordance with manufacturer's directions.
INSTALL WAX SEAL
Invert toilet on floor (cushion to
prevent damage), and install wax
ring evenly around waste flange
(horn), with tapered end of ring
facing toilet. Apply a thin bead
of sealant around toilet base.
POSITION TOILET ON FLANGE
a.
Unplug floor waste opening and install toilet
on closet flange so bolts project through
mounting holes.
b.
Loosely install retainer washers and nuts.
Side of washers marked "THIS SIDE UP"
must face up!
3
6
8a
4
5
7
CLOSET FLANGE
CLOSET BOLTS
A
INSTALL TOILET
!
a.
Position toilet squarely to wall and, with a rocking
motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS OR
BASE MAY BE DAMAGED!
b.
Install bolt covers:
1.
Make sure that the bolt cover area on the toilet is
clean and dry (see figure). Use a dry piece of cloth
or soap and waterif needed.
2.
Take plastic bolt cover and peel the brown protective
film off on both ends. The adhesive part is now visible
and ready to be placed on the toilet (see figure).
3.
Gently place the bolt cover on the toilet area (see picture) and if everything is aligned, push bolt cover
firmly so it remains in place.
4.
If not aligned, you can still take it off and put it back so it is aligned.
5.
Repeat Step 3 for second bolt cover which is to be placed on opposite side of the toilet.
6.
After 24 hours, the bolt cover adhesive has completely set off and if needed, you can remove/replace
as needed. The dual lock technology is now in place.
c.
Smooth off the bead of sealant around base. Remove excess sealant.
WAX RING
SEALANT
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
OPENING
CLOSET
BOLT
NUT
BOLT COVER
BOLTS
CLOSET FLANGE
Peel both protective films off
and stick bolt cover to toilet.
Back Side
Front Side
BOLT COVER
Before continuing, determine the type of water supply connection you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
COUPLING
NUT
COUPLING
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
CONE
WASHER
EXISTING
CONE
WASHER
EXISTING
WASHER
These parts must be used as illustrated
to insure water-tight connection. Use
of existing coupling nut may result in
water leakage. Water supply tube or
pipe must extend at least 1/2" (13 mm)
inside threaded shank of valve (does
not apply to flanged tubing).
Use existing spiral cone
washer. Fluidmaster cone
washer may not seal
completely on spiral
type supply line.
Captive cone washers
already included. No
additional washers
needed.
Use existing
coupling nut
and washer.
8b
CAUTION: DO NOT USE CONE
WASHER WITH PLASTIC SUPPLY LINE.
With correct washers in place (see
Step 8a), tighten COUPLING NUT
1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
CAUTION: Overtightening of LOCK NUT
or COUPLING NUT could result in
breakage and potential flooding.
