background image

- 2  - 

Introduction 

 
The 

DX Engineering

 

THUNDERBOLT™

 

MBVA-1UP

 is a high performance 160-10 meter 

vertical multi-band antenna that is tunable to operate with an SWR of 1.5:1 or less. Designed with 
6063 corrosion-resistant aluminum tubing and stainless steel hardware, this antenna is very durable, 
attractive, and is an optimized height of only 43 feet!  
 

DX Engineering THUNDERBOLT™ 

technology has been proven in the hostile, remote 

environment of Antarctica’s Peter I Island by the outstanding performance by the 

3Y0X 

DXpedition 

with an amazing 5,869 QSOs on 80 meters!

 

 

 
Of course, another key to performance is a good ground radial system. 32 radials, 65 feet long are 
recommended. Fewer radials will work, but with diminished results. 
 
The 

MBVA-1UP

  160-10  meter  vertical  antenna  includes  the  antenna  element,  mounting  plates, 

patented Tilt Base, Multi-Band UNUN, patented UNUN Mounting Bracket, stainless steel hardware 
and clamps.  
 

 
Features 

 

Full band coverage on 160-10 meters with an SWR under 1.5:1*

 

                       *

 

Customer supplied wide band tuner required. 

 

Power Handling up to 5 kW 

 

Only 43 ft. overall height 

 
 

Supplied Installation Items: 

 
Tilt Base 

- Precision laser cut from 3/16 in. 304 Stainless Steel, this patented tilt mounting plate is 

virtually  indestructible.  Mounts to the same mast that you use for the radial plate.  Allows for easy  
installation, tuning or severe weather lay-down. 
 

DXE-UN-43 - Multi-Band UNUN for Vertical Antenna Systems 

The 

 DXE-UN-43 

DX Engineering Multi-Band Vertical UNUN built with proven Maxi-Core

® 

Technology  is a matching device specifically designed for application with non-resonant 43 
foot tall vertical multi-band antennas. 
 
The

 DXE-UN-43

 assures the best efficiency from your vertical multi-band antenna and 

transmission line/tuner installation. Using the

 DXE-UN-43

 results in minimizing the additional 

transmission lines losses caused by SWR and allows your antenna to perform to its full 
potential. The 

DXE-UN-43

 reduces the stresses on your equipment more efficiently than similar 

competitive products.   
 
By allowing your wide-range tuner to more easily match the antenna’s complex impedance, low 
frequency performance is improved over other devices currently available. 
 

Summary of Contents for THUNDERBOLT DXE-MBVA-1UP

































Reviews: