N Connector Installation Tool
DXE-UT-80N
Patent Pending
For the DXE-N1001-S and similar Two-Piece N Connector
First properly prepare the coaxial cable with the
DXE-UT-8000
or
DXE-UT-8213
Cable Stripping Tool. Place the prepared coaxial
cable end into the body of the N connector (
DXE-N1001-S
or similar) and make sure all the strands of the center conductor of the cable
are inserted into the center pin. Then, use this simple hand-gripped tool - forget about those pliers that scarred the connector and ripped
off chunks of metal - and thread the N connector body onto the stripped cable end. Tighten the N Connector onto the coaxial cable.
When the coaxial cable is fully seated, remove the tool. Check to see that the coaxial cable is fully seated in the N connector by ensuring
the shield is visible through the larger holes and the center strands are visible in the small hole of the center pin. If all is okay, you're
ready to solder the connections. This tool allows a perfect and easy connector installation every time!
Coaxial cable properly prepped DXE-N1001-S N-Connector into DXE-UT-80N Ready for soldering
Complete and
detailed
instructions with
extra tips
and
videos
showing the tools being used can be found on the
DX Engineering web site at:
Technical Support
If you have questions about this product, or if you experience difficulties during the installation, contact DX Engineering at (330) 572-3200. You can
also e-mail us at:
For best service, please take a few minutes to review this manual before you call.
Warranty
All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year from
date of shipment. DX Engineering’s sole obligation under these warranties shall be to issue credit, repair or replace any item or part thereof which is
proved to be other than as warranted; no allowance shall be made for any labor charges of Buyer for replacement of parts, adjustment or repairs, or
any other work, unless such charges are authorized in advance by DX Engineering. If DX Engineering’s products are claimed to be defective in
material or workmanship, DX Engineering shall, upon prompt notice thereof, issue shipping instructions for return to DX Engineering
(transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived by Buyer unless made in
writing. The above warranties shall not extend to any products or parts thereof which have been subjected to any misuse or neglect, damaged by
accident, rendered defective by reason of improper installation, damaged from severe weather including floods, or abnormal environmental
conditions such as prolonged exposure to corrosives or power surges, or by the performance of repairs or alterations outside of our plant, and shall
not apply to any goods or parts thereof furnished by Buyer or acquired from others at Buyer’s specifications. In addition, DX Engineering’s
warranties do not extend to other equipment and parts manufactured by others except to the extent of the original manufacturer’s warranty to DX
Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof. These warranties provide exclusive remedies,
expressly in lieu of all other remedies including claims for special or consequential damages. SELLER NEITHER MAKES NOR ASSUMES ANY
OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION OR
LIABILITY NOT STRICTLY IN ACCORDANCE WITH THE FOREGOING.
©DX Engineering
2013
DX Engineering
®
, DXE
®
, DX Engineering, Inc.
®
, Hot Rodz
®
, Maxi-Core
®
, DX Engineering THUNDERBOLT™, DX Engineering Yagi Mechanical
®
, EZ-BUILD
®
,
TELREX
®
and Gorilla Grip
®
Stainless Steel Boom Clamps, are trademarks of PDS Electronics, Inc. No license to use or reproduce any of these trademarks or other
trademarks is given or implied. All other brands and product names are the trademarks of their respective owners.
DX Engineering 2013
P.O. Box 1491
Akron, OH 44309-1491 USA
Phone: (800) 777-0703
Technical Support and International: (330) 572-3200
Fax: (330) 572-3279
E-mail:
