DX Engineering DXE-7580FS-VA-3 Manual Download Page 12 | Manualshive

Page: 12 / 40

background image

- 11 -

4. Locate the stainless steel pivot base locking plate, backing plate, four carriage bolts, four 3/8"

flat washers, four 3/8" split lock washers and four 3/8" hex nuts. Assemble the pivot base
locking plate to the top of the heavy duty Extren® insulated channel as shown below. Tighten
the hardware.

5. Locate the stainless steel base side bottom hinge, two 1/2-13 x 1-3/4" long stainless steel hex

head bolts, two pivot bushings, four 1/2" x 1/4" stainless steel flat washers, two 1/2" stainless
steel split lock washers, and two 1/2-13 stainless steel hex nuts. Assemble the base side hinge
plate to the bottom hinge plate as shown below. Tighten the hardware.

«
...
10
11
12
13
14
...
»

Summary of Contents for DXE-7580FS-VA-3









































Reviews:

No comments

Related manuals for DXE-7580FS-VA-3

Brand: Somogyi Elektronic Pages: 8

Brand: SICK Pages: 40

Brand: BAS Pages: 3

Mantis Motorised MSAT ACU

Brand: Vislink Pages: 60

Brand: Plantec Pages: 3

Brand: RFS Pages: 8

Brand: RSI Pages: 9

Brand: GIGA-TMS Pages: 21

Brand: Globalstar Pages: 7

Brand: Label Italy Pages: 10

air Grid M2 AGM2-HP-1114

Brand: Ubiquiti Pages: 20

Brand: M2 Antenna Systems Pages: 5

Brand: Mohu Pages: 2

Brand: Maco Antennas Pages: 6

QP-AO24P14i Series

Brand: qpcom Pages: 3

Brand: JCM Technologies Pages: 28

Brand: Naxa Pages: 2

Brand: Nedap Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands