background image

- 7 - 

Install the lower tube on to the insulated channel using the two 3/8" x 2" U-Bolts, two saddle 
clamps, four flat washers, four split washers, and four nuts as shown in 

Figure 1

. Use the outer 

upper and lower holes of the channel. When tightening, observe the split washers.  When they fully 
seat (flatten out), the clamp is tight enough. Any clamp should be tightened evenly from side-to-side 
with an equal amount of thread above each nut. 

 
 
Base Section to Mounting Pipe 

Attach the completed base section to your steel ground mounted pipe using the two 

DXE-CAVS-1P

 

Saddle Clamps included, as shown in 

Figure 3

. The standard 1-1/4" galvanized water pipe (with its 

approximate 1.7" OD) is just fine for this application and can usually be found at your local home 
building supply store. Use two V-Bolts, two saddles, four nuts, four flat and four split washers.  
When tightening, observe the split washers.  When they fully seat (flatten out), the clamp is tight 
enough. Any clamp should be tightened evenly from side-to-side with an equal amount of thread 
above the nut. 

 

 
 
 
 
 
 
 
 
 
 
 
        

 

 

 

 

 

 

 

 

    

(This view shown without  

 

 

 

 

 

 

 

 

 

   insulated channel for clarity) 

 

Figure 3 

 

Assembling the Vertical Sections 

 
Assemble the vertical in an area that is flat and has sufficient room for the length of the antenna 
during assembly. Lay the element tubing out in descending diameter sizes of 1-7/8", 1-3/4", 1-5/8", 
1-1/2", 1-3/8", 1-1/4", 1-1/8", and 1" with the slits in the element tubes toward the top of the 
antenna (the 1" top element section does have slits but is installed with the slits downward). The 
bottom element section you previously mounted in the base section is 36" long and all the other 
element sections are 36" long. 
 

Note:  DXE-P8A -Penetrox A Anti-Oxidant 

should be used between all antenna element 

sections.  Penetrox is an electrical joint compound to affect a substantial electrical 
connection between metal parts such as telescoping aluminum tubing or other 
antenna pieces. It ensures high conductivity at all voltage levels by displacing 
moisture and preventing corrosion or oxidation

 

Summary of Contents for DXE-30VE-1





















Reviews: