Dwyer Instruments W.E. Anderson WE35 Series Specifications-Installation And Operating Instructions Download Page 8

Page: 8 / 12

Wiring Diagrams for

MI01-A to MI06-A1: 110 VAC, MI01-B to MI06-B: 220 VAC, MI01-C to MI06-C: 24 VAC

4-20mA POSITIONER

PSC MOTOR

CAPACITOR

SW. 1, CLOSE

SW. 2, OPEN

BRAKE

OPTIONAL

1PH-60HZ

POWER SUPPLY

4-20mA CONTROL

SIGNAL

0-10VDC or 0-5VDC

CONTROL SIGNAL

REMOVE JP2, JP3 & JP4

1K OHM FEEDBACK

POTENTIOMETER

FIELD

WIRING

HOT

NOTE:

ACTUATOR SHIPPED IN OPEN

POSITION, 20mA REPRESENTS OPEN

POSITION. DO NOT ADJUST FEEDBACK

POTENTIOMETER OR LIMIT SWITCHES

THEY ARE FACTORY SET AND DO NOT

REQUIRE CALIBRATION. TO

CALIBRATE THE OPEN AND CLOSE

POSITION, USE THE ZERO (4mA) AND

SPAN (20mA) TRIM POTENTIOMETERS.
TO CALIBRATE, OPERATE ACTUATOR

TO CLOSE POSITION AND ADJUST WITH

ZERO TRIM POT THEN OPERATE TO

OPEN POSITION AND SET USING SPAN

TRIM POT. NO FURTHER CALIBRATION IS

NECESSARY.

HEATER &

THERMOSTAT

OPTIONAL

WIRING DIAGRAM FOR 1Ph/60Hz ELECTRIC

ACTUATOR WITH 4-20mA, 0-5Vdc OR 0-10Vdc CONTROL.

JUMPER AS SHOWN BELOW IS FAIL IN

LAST POSITION UPON LOSS OF SIGNAL

SW. 3, CLOSE

SW. 4, OPEN

AUXILIARY SWITCHES

OPTIONAL

OPTIONAL EQUIPMENT

FIELD WIRING

Wiring Diagrams for

MI01-D to MI06-D: 24 VDC

4-20mA POSITIONER

PSC MOTOR

CAPACITOR

SW. 1, CLOSE

SW. 2, OPEN

BRAKE

OPTIONAL

1PH-60HZ

POWER SUPPLY

4-20mA CONTROL

SIGNAL

0-10VDC or 0-5VDC

CONTROL SIGNAL

REMOVE JP2, JP3 & JP4

1K OHM FEEDBACK

POTENTIOMETER

FIELD

WIRING

HOT

NOTE:

ACTUATOR SHIPPED IN OPEN

POSITION, 20mA REPRESENTS OPEN

POSITION. DO NOT ADJUST FEEDBACK

POTENTIOMETER OR LIMIT SWITCHES

THEY ARE FACTORY SET AND DO NOT

REQUIRE CALIBRATION. TO

CALIBRATE THE OPEN AND CLOSE

POSITION, USE THE ZERO (4mA) AND

SPAN (20mA) TRIM POTENTIOMETERS.
TO CALIBRATE, OPERATE ACTUATOR

TO CLOSE POSITION AND ADJUST WITH

ZERO TRIM POT THEN OPERATE TO

OPEN POSITION AND SET USING SPAN

TRIM POT. NO FURTHER CALIBRATION IS

NECESSARY.

HEATER &

THERMOSTAT

OPTIONAL

WIRING DIAGRAM FOR 1Ph/60Hz ELECTRIC

ACTUATOR WITH 4-20mA, 0-5Vdc OR 0-10Vdc CONTROL.

JUMPER AS SHOWN BELOW IS FAIL IN

LAST POSITION UPON LOSS OF SIGNAL

SW. 3, CLOSE

SW. 4, OPEN

AUXILIARY SWITCHES

OPTIONAL

OPTIONAL EQUIPMENT

FIELD WIRING

Summary of Contents for W.E. Anderson WE35 Series













Search results

Summary of Contents for W.E. Anderson WE35 Series

Reviews:

Brands by name

Popular brands

Dwyer Instruments W.E. Anderson WE35 Series, Specifications-Installation And Operating Instructions

Search results

Summary of Contents for W.E. Anderson WE35 Series

Reviews:

Brands by name

Popular brands