Parameter Programming
Note:
Set Point and the time programming are the only parameters accessible without
access code.
Set Point
• Press SET. Set Point value will appear on the display.
• Press SET again. The real value is shown on the display and can be modified with
the UP and DOWN arrows.
• Press SET to confirm any new values.
• Press SET and DOWN simultaneously to quit programming or wait one minute for
the display to automatically exit programming mode.
Real Time Clock
• Press SET. The Set Point value will appear on the display.
• Press the UP or DOWN arrow to change to Hour or Minute.
• Press SET to see the assigned value.
• Use the UP and DOWN arrows to set the desired value.
• Press and hold SET for 8 seconds to program value. The word “Pro” should appear
on the screen if the value has been programmed correctly.
• Press SET and DOWN simultaneously to exit or wait for the timeout.
Protected Parameters
• Press and hold SET for 8 seconds. The access code value 00 is shown on the
display.
• Using the UP and DOWN arrows, set the code (factory-set code is 00).
• Press SET to enter the code. If correct, the first parameter label will be shown on
the display (SP).
• Use the UP and DOWN arrows to move to desired parameter and SET to view
parameter value.
• While viewing a parameter value, use the UP and DOWN arrows to modify parameter
value. Use SET to enter value and exit parameter.
• The display will blink when there is an error recording a parameter in memory or
when awaiting confirmation of a value.
• Press SET and DOWN simultaneously to quit programming or wait one minute to
automatically exit programming mode.
LED Indication and Display Messages
:
Indicates if the load is connected. If continuous cool cycle is being
performed, this LED flashes (90% ON, 10% OFF). If the unit is waiting the
stopping time value stored in c0 to start a cool cycle the LED flashes (10%
ON, 90% OFF).
:
Indicates if defrosting is active.
:
Indicates an active alarm. The LED will flash if the alarm is cleared, but the
alarm condition persists.
:
Indicates when fan control relay is active. Either H7 or H8 must be set to
one of the fan control modes (FAN or FAI).
HACCP: Indicates HACCP alarm recording feature is active.
If an alarm or error occurs, the following messages will be shown and an internal
buzzer will sound.
The alarm can be cleared and buzzer silenced by pressing the SET and DOWN
buttons simultaneously. The alarm message will not be shown, but the alarm LED will
flash while the alarm condition persists.
Err =
Memory error
ErP1 =
Probe 1 error
ErP2 =
Probe 2 error
ErP3 =
Probe 3 error
Eri =
Internal parameter error. In this case enter the factory default configuration, as
described in the Resetting to Factory Defaults section.
ALH =
High temperature alarm
ALL =
Low temperature alarm
ALE =
External alarm
AEH =
High temperature and external alarm
AEL =
Low temperature and external alarm
ooo =
Open probe error
- - - =
Short circuit probe error
DON =
Defrosting activated
DOF =
Defrosting deactivated or cannot be done
CON =
Continuous cold cycle activated
COF =
Continuous cold cycle deactivated
-d- =
Defrosting (when d5 set to -d-)
Setting Keyboard Code to Zero
• Turn unit off and back on. Press and hold SET for 8 seconds. Value 00 should flash
on the display.
• Set the code to 123 using the UP and DOWN arrows.
• Press SET to confirm the code. The code is now set to 00.
Activating and Deactivating Manual Defrost Cycle
Press and hold the AUX button for 2 seconds to activate defrosting. Repeat this
process to stop the defrosting. If a cool cycle is activated, the defrosting is disabled.
Activating and Deactivating Cool Cycle
Press and hold the DOWN arrow for 8 seconds to activate a continuous cool cycle.
Repeat this process to stop the cool cycle. If defrosting is activated, the cool cycle is
disabled.
Fault Cycle
If the probe fails, the load is connected for the time set in c2 and then disconnected
for the time set in c3.
In case of memory error, the load is connected for 5 minutes and then disconnected
for 5 minutes.
On/Off Mode
This option is used to turn the control into an OFF or stand by mode, disabling the
display and outputs.
• Press and hold SET and DOWN for 8 seconds. The display will read OFF.
• Press and hold SET and DOWN for 8 seconds to return the control to normal
operation.
On/Off Light
The 2nd or 3rd relay can be configured as a lighting switch by setting the H7 or H8
parameter to Li. To activate or deactive the light relay, press and hold AUX and UP for
3 seconds.
Probe View
To view the probe not chosen in P5, press the SET and UP buttons.
HACCP
If this option is activated, the thermostat registers up to 5 high, low, and power loss
alarms. These alarms can be seen in the menu Registry of Alarms (HAC). To access
this menu, proceed to the parameters menu.
The first value (nAt) that appears is the number of registered alarms. Next, the value
of the temperature (Adx) and the time of each alarm that exists (tdx) are displayed. For
the disconnection alarm, the temperature when returning the connection is registered,
as well as the time until the correct value is reached. (Probe<Set+A1-A0)
When the elapsed time is shown it will appear dxx (days). Pressing UP, hxx (Hours)
will be shown, and pressing UP again, nxx (Minutes) will be displayed. When located
over a temperature of alarm or time, pressing AUX + UP for 3 seconds, both recorded
data of the alarm (time and temperature value) are deleted.
In the HAC menu, pressing AUX + UP keys for 3 seconds, all the recorded alarm data
is deleted.
Resetting to Factory Defaults
• Access to parameter H0 as explained in parameter programming.
• Choose desired configuration.
• For Series TSXT-xx1: H0 is set to 0
• For Series TSXT-xx2: H0 is set to 1
• For Series TSXT-xx3: H0 is set to 2
• Press SET for 8 seconds, and the thermostat will be reset.
