background image

AN24 & AN28 Annunciators  

 

Instruction Manual 

 

 

Disclaimer 

The information contained in this document is 
subject to change without notice. Dwyer 
Instruments, Inc makes no representations or 
warranties with respect to the contents hereof; 
and specifically disclaims any implied warranties 
of merchantability or fitness for a particular 
purpose. 

 

 

Read complete instructions prior to installation 
and operation of the annunciator. 

 

 

Risk of electric shock or personal injury. 

 

This product is not recommended for life support 
applications or applications where malfunctioning 
could result in personal injury or property loss. 
Anyone using this product for such applications 
does so at his/her own risk. Dwyer Instruments, 
Inc shall not be held liable for damages resulting 
from such improper use. 

 

 

WARNING 

Cancer and Reproductive Harm 

www.P65Warnings.ca.gov 

 

Limited Warranty 

Dwyer Instruments, Inc warrants this product 
against defects in material or workmanship for 
the specified period under 

“Specifications” from 

the date of shipment from the factory. Dwyer

’s 

liability under this limited warranty shall not 
exceed the purchase value, repair, or 
replacement of the defective unit. See Warranty 
Information and Terms & Conditions on 

www.dwyer-inst.com

 for complete details. 

© 2020 Dwyer Instruments, Inc. 
All rights reserved. 

Introduction 

The Series AN24/AN28 is a multipurpose panel 
mounted alarm annunciator available for four or eight 
inputs. 

It can be set up to respond to alarm conditions based 
on 8 field selectable alarm sequences, including first-
out indication. The alarm channels accept normally 
open, normally closed, NPN open collector transistor, 
and logic level inputs. Three front panel pushbuttons 
are used during sequence operation to silence the 
horn, acknowledge the first out alarm, and reset 
cleared channels as required by the sequences. 

The Series AN24/AN28 has two SPDT relays that can 
be used for additional external alarm indication, 
additional audible devices, or for process control. 

Ordering Information 

85-265 VAC* 
Model 

12-36 VDC* 
Model 

Description 

AN24-1 

AN24-2 

4 Channel 
Annunciator 

AN28-1 

AN28-2 

8 Channel 
Annunciator 

* All models may be powered from AC or DC, se

 

Specifications

 for details. 

Enclosures 

Series 

# of 

Meters 

Material 

Mounting 

PME-01

 

1

 

Low-Cost Plastic 
NEMA 4X

 

Through 
Cover

 

PME-02

 

2

 

PME-11

 

1

 

Plastic NEMA 4X

 

Through 
Door

 

PME-12

 

2

 

PME-13

 

3

 

PME-14

 

4

 

PME-15

 

5

 

PME-16

 

6

 

Summary of Contents for AN24 Series






















Reviews: