DWT SBM-1050 DT, Original Instructions Manual

Page: 20 / 141

19
English
parts.
This will ensure that the safety of the power tool
is maintained�
•
Follow instruction for lubricating and changing ac-
cessories�
•
Special
safety warnings
Wear ear protectors when impact drilling.
Expo-
sure to noise can cause hearing loss�
NOTE:
The above warning applies only to impact drills
and may be omitted for drills other than impact drills�
• Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury�
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock�
•
Safety guidelines during
power tool operation
The workpiece shall be fastened� Fixed devices or vice
shall be used to fasten the workpiece, which will be more
secure than holding the workpiece with your hands�
•
Considering that asbestos may cause cancer, as-
bestos-containing materials shall not be processed�
•
The power tool could be put down only after the
parts of power tool is completely static� Accessory on
the power tool might be clamped during work, which
may make it difficult for you to control the power tool.
•
Power tool with damaged electric wires shall not be
used� If electric wires of the power supply are damaged
during the work, you shall not touch the damaged elec-
tric wires and shall pull out the plug immediately� Dam-
aged electric wires will raise the risk of electric shock�
•
When using power tools outdoor, you must install
fault current (FI) protection switch on the power tool�
• Appropriate detector shall be used to find the loca
-
tion of hidden power wires� Or you should obtain rel-
evant information from local power supply unit� Drilling
electric wires will cause fire and electric shock. Dam
-
aged gas pipe will cause exploration� If water pipes are
punctured, damage will be caused to property�
•
In case a accessory installed on the power tool is
clamped, you shall shut down the power tool and stay
calm� At that time, the power tool will produce extreme-
ly high reactive torque thus resulting in return stroke�
The accessory installed on the power tool are likely to
be clamped, for example: hypercharge of power tool or
skewing of accessory installed on the power tool dur-
ing work�
•
If hidden electric wires or power lines of the power
tool itself might be cut off during work, you must hold
the insulated handle to operate the power tool� When
the power tool is in touch with a charged line, the metal
parts on the power tool will conduct electricity and may
cause the operator to get an electric shock�
•
During work, you must tightly hold the power tool
and ensure you stand firmly. You should hold the pow
-
er tool with your hands�
•
When operating and using the power tool, you can
only hold switch position of the main handle rather than
other parts�
•
Avoid stopping an power tool motor when loaded�
•
Never remove any chips or fragments with your
power tool’s motor running�
•
When working, follow the position of the power sup-
ply cable� Avoid winding it around your legs or arms�
•
Use only sharp drill bits without defects - it will make
working with the power tool easier�
• The modification of the drill bits design and the use
of removable orifices and accessories not envisaged
for this power tool is strictly forbidden�
•
Do not apply excessive pressure when operating the
power tool - it can jam the drill bit and overload the
engine�
•
Do not allow drill bits to jam in the material pro-
cessed� If this occurs, do not try to release them by
means of the power tool engine� This can put the pow-
er tool out of order�
•
Striking out drill bits jammed in the material pro-
cessed with a hammer or other objects is strictly for-
bidden - metal fragments can hurt both the operator
and the people nearby�
•
Avoid overheating your power tool, when using it for
a long time�
Symbols used in
the manual
Following symbols are used in the operation manual,
please remember their meanings� Correct interpreta-
tion of the symbols will allow correct and safe use of
the power tool�
Symbol Meaning
Impact drill
Sections marked gray - soft
grip (with insulated surface)�
SBM ...
Serial number sticker:
SBM ��� - model;
XX - date of manufacture;
XXXXXXX - serial number�
Read all safety regulations
and instructions�
Wear safety goggles�
Wear ear protectors�
Wear a dust mask�
Disconnect the power tool
from the mains before
installation or adjustment�
Autogoods “130”
130.com.ua