DW SitePro SLR202GR Operating And Safety Instructions Manual Download Page 2

2

GENERAL SAFETY RULES

Working safely with this instrument is possible only when the operating and safety infor-
mation are read completely and the instructions contained therein are strictly followed. 
The use of controls, adjustments, or the performance of procedures other than those 
specified herein may result in hazardous radiation exposure. 

DO NOT stare into the laser beams

DO NOT direct the laser beam at other persons. 
DO NOT disassemble the instrument or attempt to perform any internal servicing.

 Laser 

class is indicated on the instrument. Repair and servicing of this laser are to be per-
formed only by SitePro or authorized service centers.

•   When attaching the instrument to a tripod, make sure the instrument is securely 

fixed. The tripod leg clamps should be securely fastened. If not securely fastened 
or tightened, the main unit could fall off or the tripod could fall over.

•   The laser should not be stored or used in extreme temperature or during rapid 

temperature change. The laser may not function properly if used out of the ambi-
ent temperature range.

•   Store inside the carry case and place in a dry area not subject to vibration, dust 

or high moisture. If the storage temperature and ambient temperature for usage 
vary significantly, leave the laser in its case until it can adjust to the ambient 
temperature.

•   The laser should be transported or carried carefully to avoid impact or vibration.
•   The laser should be stored in the carry case and packed with cushioning material. 

Always handle the laser with care.

Dave White’s Site Pro, LLC
www.sitepro.us.com

Made in China

Laser radiation. Do not stare into the beam or view directly with optical instruments. 
Class 2M lasers product. Complies with  21 CFR 1040.10 & 1040.11 except for 
deviations persuant to Laser Notice 50, June 6, 2007

Radiación laser. No mire hacia el rayo. No mirar con instrumentos ópticos. Producto 
láser  de Clase 2M. Cumple con las normas 21 CFR 1040.10 y 1040.11, excepto 
por las desviaciones conforme al Aviso para láseres 50, 6 de junio de 2007

Rayonnement laser. Ne pas regarder le rayon. Ne pas regarder avec instruments . 
Produit laser de Classe 2M. Conforme à 21 CFR 1040.10 et 1040.11, sauf pour 
les écarts suivant l’Avis laser 50, 24/6/2007

IEC 60825-1:2007-03

≤ 1 mW @ 630 - 670 nm

2M

Summary of Contents for SitePro SLR202GR

















Reviews: