DVP 9215001 Installation Manual Download Page 7

MUM-49A

MA.15-MA.15S-MV.15S-MA.30P-MV.30P

17/11/03-R.2

D.V.P. Vacuum Technology S.r.l.

Pag.2

MODEL

MA.15

(MV.15S) MA.15S (MV.30P) MA.30P

Volt

V

230

12

24

230

12

24

230

12

24

Frequecy

Hz

50

60

cc

cc

50

60

cc

cc

50

60

cc

cc

Nominale flow rate

nl/min

15

18

15

15

18

15

30

33

30

Final pressure (Asb.)

mbar (hPa)

100

15

80

Motor power

W

95*

15

(140*) 45

30

(140*) 45

30

Noise level

dB(A)

50

52

50

52

53

52

53

Weight

kg

1,8

1,2

(2,9) 3,7

1,8

(2,9) 3,9

2

Operat. temp.(ambient temp 20°C)

°C - - -

- - -

40

42

40

45

50÷55

(40)30 (45)35

55

50

Req. room temp for installation

°C

0÷40

Ambient temp. for storage/transport

°C

0÷40

Inlet connection

"G

1/8

Service factor

S3 25%

S1

S1

S1

(*) Required power.

1 INTRODUCTION

1.1 purpose of the manual.

This  manual  illustrates  the  correct  procedures
for  unpacking,  installing,  use,  maintenance,
store  and  dispose  pumps  MA  series.  Before
beginning  to  operate  you  have  to  attentively
read the instructions contained in this manual.
In the manual two simbologies are employed:

  The  first  refers  to  instructions  that  if  not

followed can cause damages to the pump.

The second refers to instructions that
if  followed  can  generate  damages  to
the pump.

All  the  measuring  units  used  in  the  present
manual  are  in  conformity  to  the  International
System. The characteristics of the products can
vary without prior notice.

2 INSTALLATION

2.1 Unpack.

Check  that  the  pack  is  not  damaged,  on  the
contrary  check  that  the  pump  operates
correctly.  In  case  of  damages,  please  send
claim  in  writing  to  the  carrier,  also  pointing
out  the  delivery  note  number,  date  and  notify
the seller.
Open the pack and remove the possible residues
of  material  of  packing  from  the  pump.  Should
the  pump  is  not  immediately  installed,  pack  it
again and store accordingly to the table.

2.2 User system.

Make  sure  that  the  user  system  is  not
contaminated  from  harmful  substances  during
the operations of installation.

Install  an  isolation  valve  between  pump

and system if you desire that it remains under
vacuum also when the pump is  not  operating.
Make  sure  that  vibrations  or  tensions  are  not
transmitted to the connections of the pump.

2.3 Positioning.

To assure the perfect operation it is
necessary that the pump is installed
in  a  well  ventilated  room  in

horizontal  position  and  that  during  the
operations it  is  not  attainable  from  any  part
of the body.

It is absolutely necessary to avoid that the warm
air  remain  inside  the  installation  vane.  Do  not
put  any  elements  near  the  cooling  fan  of  the
motor that alter the normal airflow.
The  pump  is  supplied  with  fixing  points,
therefore, it must be fixed on the user system to
avoid  dangers  in  case  of  case  turnover  during
transport.

 
2.4 Electric connection.

The  electric  connection  must  be
performed  by  trained  personnel  in
compliance  with  local  electrical

standard in force.

Summary of Contents for 9215001










Reviews: