Dustbane Tracker 71000, Parts & Operation Manual

Page: 7 / 32

7 Parts & Operations Manual Tracker 7 Parts & Operations Manual Tracker
On-Board Tool Cleaning
These vacuums are equipped with on-board cleaning tools including a metal
telescopic power wand, stretch hose, dusting brush and a crevice tool.
1.
To use the cleaning tools, lift the hose handle straight up from the vacuum
(Fig. 1 ).
2.
extend the wand by pulling the button back and pulling the smaller wand
out of the larger wand (Fig. 2 ).
3.
Attach any of the on-board tools to the end of the wand or if you do not
need the wand, any tool can be connected directly onto the hose handle.
How to Replace the Vacuum Belt
CAUTION: Unplug the vacuum cleaner before performing any of these steps.
How to Remove the Bottom Plate
1. Place the vacuum cleaner in the low position by pressing the foot
pedal release twice while reclining the handle. Turn the vacuum over.
2.
Slide the clips toward each other (Fig. 3 ).
3. Remove the bottom plate.
How to Replace the Belt
1. Turn the unit over and remove the bottom plate as described in the above section.
2.
Remove the belt guard (Fig. 4) . Remove the agitator by pulling it straight out (Fig. 5 ).
3.
Remove the belt from the agitator.
4. Loop a new belt over the motor pulley (Fig. 6 ) and over the end of the agitator.
5. Stretch the belt over the agitator while inserting it back into the nozzle housing.
6.
Reinsert the belt guard.
7. Spin the agitator by hand to make sure it turns smoothly and the new belt is
properly aligned.
8. Replace the bottom plate by hooking the front end of the plate into the two ribs on
the front end of the nozzle housing. Press the bottom plate into place and fasten it
with the two screws.
NOTE: To ensure maximum cleaning effi ciency, check the belt regularly to ensure it is in good
condition. Replace the belt if it is stretched, cracked or if excessive slipping is occurring.
Fig. 1
Fig. 2
Fig.
3
Fig.
4
Fig.
5
Fig.
6
On-Board Tool Cleaning
These vacuums are equipped with on-board cleaning tools including a metal
telescopic power wand, stretch hose, dusting brush and a crevice tool.
• To use the cleaning tools, lift the hose handle straight up from
the vacuum (Fig. 1).
• Extend the wand by pulling the button back and pulling the smaller
wand out of the larger wand (Fig. 2).
• Attach any of the on-board tools to the end of the wand or if you
do not need the wand, any tool can be connected directly onto
the hose handle.
How to Replace the Vacuum Belt
CAUTION: Unplug the vacuum cleaner before performing any of these steps.
How to Remove the Bottom Plate
• Place the vacuum cleaner in the low position by pressing the foot
pedal release twice while reclining the handle. Turn the vacuum over.
• Slide the clips toward each other (Fig. 3).
• Remove the bottom plate.
How to Replace the Belt
• Turn the unit over and remove the bottom plate as described in the above section.
• Remove the belt guard (Fig. 4). Remove the agitator by pulling it straight out (Fig. 5).
• Remove the belt from the agitator.
• Loop a new belt over the motor pulley (Fig. 6) and over the end of the
agitator.
• Stretch the belt over the agitator while inserting it back into the nozzle
housing.
• Reinsert the belt guard.
• Spin the agitator by hand to make sure it turns smoothly and the new belt
is properly aligned.
• Replace the bottom plate by hooking the front end of the plate into the two ribs
on the front end of the nozzle housing. Press the bottom plate into place
and fasten it with the two screws.
NOTE: To ensure maximum cleaning effi ciency, check the belt regularly to ensure
it is in good condition. Replace the belt if it is stretched, cracked or if excessive
slipping is occurring.