21
ENGLISH
ENGLISH
21
detergent thus allowing a perfect drying. As long as time goes by the continuous scraping
rounds off and splits the sharp edge in contact with the floor, thus reducing the drying
efficacy and therefore requiring the replacement of the blades. Therefore, often check
their state of wear and tear.
Exchanging or replacing the blades:
•
stop the machine and press the emergency button (fig. 8, ref. 2); engage the parking
brake by means of the pedal (fig. 8, ref. 12);
•
lower the squeegee by using the proper lever (fig. 8, ref. 11);
•
take off the squeegee (fig. 2, ref. 8) from its supporting plate (fig. 9, ref. 2) by
unscrewing completely the two knobs (fig. 9, ref. 3);
•
slide out the sleeve of the suction tube (fig. 9, ref. 4) from the squeegee.
Front blade
:
•
unscrew the knobs (fig. 19, ref. 1);
•
remove the blade clamps (fig. 19, ref. 3);
•
take out the blade (fig. 19, ref. 4);
•
fit in the same blade inverting the edge in contact with the floor until all the four edges
are worn, or else fit in a new blade;
•
put the blade clamp (fig. 19, ref. 3) back;
•
screw down all the knobs (fig. 19, ref. 1).
Rear blade
:
•
unhook the hook clamp (fig. 19, rif. 8);
•
slide out the two blade clamps (fig. 19, ref. 7) by first pushing them outwards with
respect to the squeegee unit (fig. 19, ref. 5) and then taking them out;
•
remove the blade (fig. 19, ref. 6);
•
fit in the same blade inverting the edge in contact with the floor until all the four edges
are worn, or else fit in a new blade embedding it in the screws of the squeegee unit
(fig. 19, ref. 5);
•
put the two blade clamps (fig. 19, ref. 7) back, centering the largest part of the slots on
the fixing screws of the squeegee unit (fig. 19, ref. 5) and then pushing the blade
clamps towards the inside of the squeegee itself;
•
hook the clamp (fig. 19, ref. 8) again.
Insert the squeegee back on its support following the instructions reported in §6.2.
9.2.4 Fuses: replacement
To replace the fuses in the control panel of the machine, proceed as follows:
•
stop the machine and press the emergency button (fig. 8, ref. 2); engage the parking
brake by means of the pedal (fig. 8, ref. 12);
•
remove the fuse cover (fig. 20, ref. 1);
•
with the tweezers supplied with the machine take out the blown fuses and replace
them with new ones of the same amperage;
•
reclose the fuse cover.
WARNING
The fuse FU7 must NOT be fitted if the machine is provided with gel batteries.
To replace the fuses inside the electrical box, proceed as follows:
•
stop the machine and press the emergency button (fig. 8, ref. 2); engage the parking
brake by means of the pedal (fig. 8, ref. 12);
•
remove the bonnet (fig. 2, ref. 4);
•
remove the cover of the electrical box (fig. 21, ref. 1);
•
with the tweezers supplied with the machine take out the blown fuses and replace
them with new ones of the same amperage;
•
re-close the cover of the electrical box;
Summary of Contents for Hurricane 850 XTT
