Durr Dental XR 24 Installation And Operating Instructions Manual Download Page 3

3

IMPORTANT INFORMATION

1. Notes

1.1 CE - Labeling

This product bears the CE- Labeling in
accordance with the guidelines of the
Medical Products Committee 93/42/EWG and
satisfies all criteria of the Appendix I to said
guidelines.

1.2 Electromagnetic Compatibility

• This product conforms to all requirements

laid down for Electromagnetic Compatibility
of Medical Appliances.

1.3 General Notes

• These Installation and Operating

Instructions form an integral part of the unit.
They must be kept close to the unit and in
readiness whenever required. Precise
observance of these instructions is a pre-
condition for use of the unit for the intended
purpose and for its correct installation and
operation.
These Installation and Operating
Instructions should be passed on to any
future purchaser or explained to any new
operator.

• Safety for the operator as well as trouble-

free operation of the unit are only ensured if
use is made of original equipment parts.
Moreover, use may only be made of those
accessories that are specified in the
technical documentation or that have been
expressly approved and released by Dürr
Dental for the intended purpose.

Any warranty or 

guarantee

 becomes

invalid

 in the case where parts or

accessories are used which are not
supplied by Dürr Dental.

• Dürr Dental only regard themselves as

being responsible for the equipment with
regard to safety, reliability and proper
functioning if assembly, resettings,
changes or modifications, extensions and
repairs have been carried out by Dürr
Dental or an agency authorized by Dürr
Dental and if the equipment is used in
conformity with the Installation and

Operating Instructions.

• The developer unit herein described

conforms to the relevant safety standards
valid at this time. All switches, processes,
trade marks, software programs and
appliances named in this document are
registered names.

• Any reprinting of the technical

documentation, in whole or in part, is
subject to prior written approval of Dürr
Dental.

1.4 General Safety Information

This appliance has been so designed and
constructed by Dürr Dental that any danger
arising from the use of this product is
virtually excluded provided it is fitted
according to the instructions. However, in
order to avoid any possible damage or injury
we are obliged to point out the following
safety measures.

• When operating this appliance all local

rules and regulations must be observed!
Any modification whatsoever is not
permitted: any guarantees covered by
Dürr Dental thus become invalid. In the
interests of ensuring problem-free running
the owner and operator are responsible for
observing all rules and regulations.

• Retain all packing material for possible

return of the product to the manufacturer.
Take care that it does not fall into the hands
of children. Only the original packing
guarantees optimal safety of the appliance
during transport.

Should return of the product to the
manufacturers be necessary during the
guarantee period, Dürr Dental accepts no
responsibility for damage occurring during
transport where the original packaging
was not used!

• This product is a technical appliance and

may only be installed and operated or
used by someone who has been trained or
who has experience of how to use the
appliance correctly.

• Before every use the operator must check

the functional safety and the condition of
the appliance.

Summary of Contents for XR 24




















Reviews: