DUROMAX XP85000E User Manual Download Page 60

Page: 60 / 74

Mode

Description

Engine will not start

Engine Switch is “Off”

Set engine switch to “run”

Fuel Valve is “Closed”

Turn fuel valve to “open”

Choke is open

Close the choke

Engine is out of fuel

Add fuel

Fuel is old or contaminated

Change fuel

Spark Plug is dirty

Clean spark plug

Spark Plug is broken

Replace spark plug

Generator is not level

Move generator to a level
surface

Oil is low.

Add / change oil

Engine runs, but there

is no electrical output

Circuit breaker is “Off”

Turn “on” circuit breaker

Wiring connection is bad

Replace extension cord(s)

Device connected to generator
is malfunctioning

Disconnect malfunctioning
device

Generator runs, but

does not support all

electrical devices

connected

Generator is overloaded

Disconnect 1 or more items to
reduce the load

Device connected to generator
is bad

Disconnect malfunctioning
device

Air Cleaner is dirty.

Clean / replace the air filter

TROUBLESHOOTING

Summary of Contents for XP85000E











































































Search results

Summary of Contents for XP85000E

Reviews:

Brands by name

Popular brands

DUROMAX XP85000E, User Manual

Search results

Summary of Contents for XP85000E

Reviews:

Brands by name

Popular brands