manualshive.com logo in svg

DUROMAX XP85000E, User Manual

Share
Download
DUROMAX XP85000E User Manual Download Page 3

1.

Introduction  ....................................................................................................................  

6

General Safety Procedures  ...........................................................................................  

8

Unit and Purchase Information .................................................................................. 

12

Carbon Monoxide Safety .............................................................................................  

13

Introduction

4.

Checking the Oil  ...........................................................................................................  

30

Check the Gas Level  .....................................................................................................  

31

Starting the Generator  ................................................................................................  

32

Starting the Generator Using Recoil Start  .................................................................  

34

Starting the Generator

3.

Shipping Braces  ............................................................................................................  

21

Wheel Kit Installation ....................................................................................................  

22

Connect the Battery  .................................................................................................... 

24

Adding Oil ......................................................................................................................  

25

Adding Gasoline ............................................................................................................  

26

Grounding the Generator  ...........................................................................................  

27

High Altitude Operation  ..............................................................................................  

27

Generator Setup

5.

AC Usage ........................................................................................................................  

38

Connecting a Load to the Generator ..........................................................................  

40

DC Usage ........................................................................................................................  

42

Using the Generator

2.

Quick Start Guide  .........................................................................................................  

14

Generator Components ...............................................................................................  

16

Package Contents .........................................................................................................  

18

Quick Start

Summary of Contents for XP85000E











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands