background image

USING THE GENERATOR

AC Usage

The total running wattage requirement of the electrical devices connected to the generator should 
not exceed the rated wattage of the generator itself. To calculate the total wattage requirement of 

the electrical devices you wish to connect, find the rated (or running) wattage of each device. This 

number should be listed somewhere on the device or in its instruction manual.

If you cannot find this wattage, you may calculate it by multiplying the Voltage requirement by the 
Amperage drawn: Watts = Volts x Amps. If these specifications are not available, you may estimate 

the Watts required by your device by using the chart on the next page.

Once you have found the rated wattage requirement of each electrical device, add these numbers 

to find the total rated wattage you wish to draw from the generator. If this number exceeds 

the rated wattage of the generator, DO NOT connect all these devices. Select a combination of 
electrical devices, which has a total rated wattage lower than or equal to the rated wattage of the 
generator.

Fuel Source

Rated (Running Wattage)

Surge (Peak) Wattage

Gasoline

3850

4850

Propane

3650

4600

46

 

You may connect electrical devices running on AC current according to their wattage 
requirements. 

 

The chart below shows the rated and surge wattage of your generator according to its model 
number. 

 

The rated wattage corresponds to the maximum wattage the generator can output on a 
continuous basis. 

 

The surge wattage corresponds to the maximum amount of power the generator can output for 
a short period of time. Many electrical devices such as refrigerators require short bursts of extra 
power, in addition to the rated wattage listed by the device, to stop and start their motors. The 
surge wattage ability of the generator covers this extra power requirement.

Summary of Contents for XP4850HX



















































































Reviews: