background image

58

WARRANTY

3-year Warranty

All DuroMax Power Equipment warrant the original purchasers to a 3-year Parts Warranty 

(Residential 

Use ONLY: Unusually heavy or commercial use is covered for  a period of 1-year) in the event of  
failure due to defects in electrical or mechanical components. Freight on any items submitted for 
replacement or repair under the Warranty are the responsibility of the equipment owner. This 
warranty is non-transferable and only valid to the original purchaser.

Warranty Exclusions

The DuroMax Power Equipment warranty does not cover repairs or returns when the fault is:
Normal Wear and Tear, Installation Use or Maintenance Services, Cosmetic defects, Accessories,
Failures due to acts of God or Natural Disasters, or problems related to/from aftermarket or non-
OEM parts.

Warranty Limitations

DuroMax Power Equipment does not claim or hold any obligation to loss of time, freight charges,
use of product, or any incidental damages from the use of this product. THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED.

U.S. FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The U.S. Environmental Protection Agency (EPA), California Air Resources Board, and DuroMax 

Power Equipment are pleased to explain the emissions control system’s warranty on your 

2022/2023 small off-road engine.
In California, new small off-road engines must be designed, built, and equipped to meet the State’s

stringent anti-smog standards. DuroMax Power Equipment must warrant the emissions control

system on your small off-road engine for the period listed below provided there has been no 
abuse, neglect, or improper maintenance of your small off-road engine leading to the failure of the 

emission control system.
Your emissions control system may include parts such as: carburetors or the fuel injection system,

ignition system, catalytic converters, fuel tanks, fuel lines(for liquid fuel and fuel vapors), fuel caps,
valves, filters, clamps, connectors, and other associated components. Also, included may be hoses,

belts, sensors, and other emission-related assemblies.

Where a warrantable condition exists, DuroMax Power Equipment will repair your small off-road

engine at no cost to you including diagnosis, parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE:

This emissions control system is warranted for two years. If any emissions-related part on your 

small off-road engine is defective, the part will be repaired or replaced by DuroMax Power 

Equipment.

Summary of Contents for XP18HPE

































































Reviews: