manualshive.com logo in svg

DUROMAX XP10000E, User Manual

Share
Download
DUROMAX XP10000E User Manual Download Page 42

Plug in devices

Turn breaker on

Plug in devices to the appropriate receptacle. When using 

the generator in 120/240v mode, balance the load as closely 

as possible. Placing more load on one side of the circuit will 

reduce the breaker trip period.

Flip the circuit breaker up to the on position to allow power to 

the receptacles.

1.

2.

42

USING THE GENERATOR (CONTINUED)

Connecting a load to the generator

NOTE: Be sure to attach devices to the correct receptacle (outlet).

 

 

●

120v devices can be directly connected to the 120v ONLY receptacles. 

 

●

120v devices can be connected to the 120/240v receptacle using an appropriate adapter. 

 

●

240v devices can ONLY be connected to the 240v receptacle.

CAUTION

: Do not connect 50Hz or 3-phase loads to the generator.

Turn on connected devices

Start or turn on appliances starting with the biggest loads 

first.

3.

Summary of Contents for XP10000E













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands