DUROMAX XP10000E User Manual Download Page 20

Page: 20 / 76

PACKAGE CONTENTS

Your generator comes with the items listed below. Please check to see that all of the following
items are included with your generator.

●

Note: Actual tools may differ in appearance or design from image shown.

Double Sided

Screw Driver

Oil Funnel w/ hose

Spanner

DC Charge Cables

Spark Plug Wrench

Plug Ends

Phillips and slot blade

screwdriver used for generator

maintenance.

Used to add oil to the

generator without messy spills.

Assorted wrenches used in

generator maintenance and

assembly. Commonly 8mm,

10mm, 13mm, and 15mm.

Used in conjunction with the

charging posts to charge 12v

automotive style batteries or

small DC appliances.

Used in spark plug

maintenance, inspection, and

installation.

Plug heads for the receptacles

found on the generator are

included to make or rewire

your own cords.

Summary of Contents for XP10000E













































































Search results

Summary of Contents for XP10000E

Reviews:

Brands by name

Popular brands

DUROMAX XP10000E, User Manual

Search results

Summary of Contents for XP10000E

Reviews:

Brands by name

Popular brands