background image

m&G DurAVent lImIteD lIfetIme WArrAnty

M&G DuraVent, Inc. (“DuraVent”) provides this limited lifetime warranty for all of its products with the exception of Ventinox® (lifetime),  and 

PolyPro® (ten years). Subject to the limitations set forth below, DuraVent warrants that its products will be free from defects in material or 

manufacturing, if properly installed, maintained and used. DuraVent products are fully warranted if installed only by a professional installer.  

This Warranty is transferable from the original homeowner to the buyer of the home. This warranty does not cover normal wear and tear, 

smoke damage or damage caused by chimney fires, acts of God, or any product that was: (1) purchased other than from an authorized 

DuraVent dealer, retailer or distributor; (2) modified or altered; (3) improperly serviced, inspected or cleaned; or (4) subject to negligence or 

any use not in accordance with the installation instructions included with the product as determined by DuraVent. Installation instructions 

are available online at 

www.duravent.com

 under Support/Literature and through our Customer Service Department 800-835-4429 or 

[email protected]

. This limited lifetime warranty applies only to parts manufactured by DuraVent.

DuraVent provides the following warranties for its products: One Hundred Percent (100%) MSRP 15 years from the date of purchase, and Fifty 

Percent (50%) thereafter, except for the following limitations on: all Termination Caps and DuraBlack® are warranted at One Hundred Percent 

(100%) for five years. 

All warranty obligations of DuraVent shall be limited to repair or replacement of the defective product pursuant to the terms and conditions 

applicable to each product line. These remedies shall constitute DuraVent’s sole obligation and sole remedy under this warranty. This warranty 

provides no cash surrender value. The terms and conditions of this warranty may not be modified, altered or waived by any action, inaction or 

representation, whether oral or in writing, except upon the express, written authority of an executive officer of DuraVent. 

Corn, bio-fuels, driftwood or other wood containing salt, preservative-treated lumber, plastic and household trash or garbage, or wood pellets 

containing such materials must not be burned in the appliance or fireplace. In case of a chimney fire, the chimney must be inspected and 

approved by a certified Chimney Sweep before reuse. After each annual inspection, maintenance, and cleaning, the certified Chimney Sweep 

must fill out and date the appropriate section of the warranty card provided with the chimney liner.

LIMITATIONS ON INTERNET SALES: Notwithstanding any other terms or conditions of this Limited Lifetime Warranty, DuraVent provides no 

warranty for the following specific products if such products are not installed by a qualified professional installer: DuraTech®, DuraPlus HTC®, 

DuraChimney® II, PelletVent Pro®, DirectVent Pro®, FasNSeal®, FasNSeal® W2, FasNSeal® Flex, and PolyPro®, and M&G DuraVent’s relining 

products including DuraLiner®, DuraFlex® (SW, Pro, 316, 304), and Ventinox®. For purposes of this warranty, a trained professional installer is 

defined as one of the following: licensed contractors with prior chimney installation experience, CSIA Certified Chimney Sweeps, NFI Certified 

Specialists, or WETT Certified Professionals.

DuraVent must be notified and given the opportunity to inspect defective product prior to replacement under the terms of this limited lifetime 

warranty. All warranty claims must be submitted with proof of purchase. Labor and installation costs are not covered under this warranty. To 

obtain warranty service contact: DuraVent Warranty Service, 877 Cotting Ct., Vacaville CA 95688, or call 800-835-4429. 

WHERE LAWFUL, DURAVENT DISCLAIMS ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL DURAVENT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, 

PUNITIVE OR SPECIAL DAMAGES OR DIRECT OR INDIRECT LOSS OF ANY KIND, INCLUDING BUT NOT LIMITED TO PROPERTY DAMAGE AND 

PERSONAL INJURY. DURAVENT’S ENTIRE LIABILITY IS LIMITED TO THE PURCHASE PRICE OF THIS PRODUCT. SOME STATES DO NOT ALLOW 

LIMITATIONS ON IMPLIED WARRANTIES, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE 

LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO 

HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. 

For the most up-to-date installation instructions, see 

www. duravent.com

REV 3.22.2012

Manufactured in Vacaville CA and Albany NY

DuraPlus  is a registered trademark of the M&G DuraVent, Inc.

All rights reserved. Made in the USA. M&G DuraVent is a member of M&G Group. ©2012

Customer Service Support 800-835-4429   707-446-4740 FAX   www.duravent.com

L119  04/2012

Summary of Contents for duraplus

























Reviews: