background image

39

1 4 7 C   D R I L L  

 

O P E R A T I N G   I N S T R U C T I O N S

Section 6: Lubrication 

All 147C Grain Drill are completely serviced at the factory before shipping.  However, the operator should make a 

check of all grease fittings on the unit before beginning to operate it so as to become familiar with their location and the 

correct service schedule.

Use only a high quality, multi-purpose grease when lubricating the unit.  Make sure all fittings and the nozzle of the 

grease applicator are clean before applying the grease.  If any grease fittings are missing, replace them immediately.

Lubricating of all pillow block and flange-type self-aligning ball or roller bearings should be done slowly to help 

prevent bearing seal damage.  Use caution when using a high pressure, high volume gun.

 

Description    

 

Type    

Frequency  

No. Zerks

 

1.   Swivel Wheel Pivot   

Grease   

20 Hrs.  

 

1

 

2.   Torque Tube Bushings  

Grease   

40 Hrs.  

 

2

 

3.   Universal Joints  

 

Grease   

40 Hrs.  

 

2

 

4.   Square Drive Line    

Grease   

40 Hrs.  

 

2

 

5.   Feed Wheel Shaft    

Grease   

100 Hrs. 

 

8

 

6.   Roller Chains  

 

Oil  

 

Daily In Dusty Conditions 

 

7.   Tool Bar Bushing    

Grease   

20 Hrs.  

 

2

 

8.   Lift Arm Bushing    

Grease   

20 Hrs.  

 

2

 

9.   Lift Arm    

 

Grease   

20 Hrs.  

 

2

 

10. Drive Wheel Frame   

Grease   

20 Hrs.  

 

2

 

11. Packer Wheel Bearings and Coulter-Disk Bearings are Non-Relubable.

 

12. Cylinder Clevis Pin   

Grease   

20 Hrs.  

 

1

swivel wheel pivot 

lubrication zerk 

Summary of Contents for HAYBUSTER 147C

























































































































Reviews: