Duracraft CZ-700E, User Instructions

Page: 5 / 62

5
ENGLISH
4. Fix the two feet (16) on both ends of the
base of the convector. Adjust the feet (16)
so that the plastic pegs on the upper sides
are pushed into the special cavities on the
base of the convector. Now screw the feet
(16) on tightly with wing bolts. Make sure
that the feet (16) are firmly fixed to the
convector. (Fig. 1)
5. Place the convector upright on a firm, even
surface. Make sure it is standing safely, so
that it cannot tip over or fall off. A safely
distance of 100cm from other objects must
be observed.
USER’S MANUAL
CZ-700E Convector with power switch and
rotary thermostat switch
CZ-700FE Convector with turbo-fan, power
switches and rotary thermostat switch
1. Make sure that the power switches (3 + 4)
are in the OFF position (5). Insert the plug
(15) into the wall socket.
Do not touch the
power cable with wet hands.
2. Make sure that the air intake vents (14)
and air exhaust vents (2) are not blocked.
The air intake vents (14) and air exhaust
vents (2) must always be free during the
heating operation.
3. Use the power switches (3), the rotary
thermostat switch (10) and /or the turbo-fan
(4) for the heating operation, according to
the model and the operating instructions.
4. When the convector is not in use, or when
it is moved, cleaned or stored away, switch
all power switches (3 + 4) to the OFF
position (5) and disconnect the plug (15)
from the power socket. Always use the
transport grips (17) at the sides of the
convector for transport purposes.
Power switches and rotary thermostat
switch
1.
By pressing the power switches (3 + 4)
you can choose between four settings:
0
OFF (5)
I Warm air 800 Watt (6)
II Warm air 1200 Watt (7)
III Hot air 2000 Watt (8)
2. Turn the rotary thermostat switch (10) in a
clockwise direction to the highest position.
The power lamps (18) of the power
switches (3) in use light up.
3. When the desired room temperature has
been reached, turn the rotary thermostat
switch (10) in an
anti-clockwise direction
until you hear a clicking noise. The
convector has now switched off the heating
operation.
4. Now turn the rotary thermostat switch (10)
only slightly back in a
clockwise direction.
The convector will now automatically switch
the heating function on and off and thus
maintain the desired room temperature. The
power lamps (18) will be switched on and
off accordingly.
5. The further you turn the rotary thermostat
switch (10) in a
clockwise direction, the
higher the heating temperature will be.
6. When the thermostat is set at the lowest
temperature (11) and at least one of the
power switches (3) is switched on, the
convector starts heating, as soon as the
room temperature drops to below + 5 °C.
The convector will then continue the
heating operation until the room
temperature has risen above + 5 °C.
7. When the rotary thermostat switch (10) is
set at the highest position (12), you cannot
turn it further in a
clockwise direction. It
can then only be turned back in an
anti-clockwise direction.
Turbo-Fan (nur CZ-700FE)
1.
Start operating the convector as described
in Points 1 and 2 of
„Power switches and
rotary thermostat switch “ .
2. Switch the turbo-fan on with the power
switch (4). The power lamp (18) lights up.
3. Now continue as described from Point 3
onwards of
„Power switches and rotary
thermostat switch“ .
4. If you wish to heat without the turbo-fan,
switch the power switch for the turbo fan
(4) to the OFF position (5).
Overheating protection
1.
The convector is equipped with overheating
protection, which switches off the convector
automatically if it overheats.