Duplo DF-990 Instruction Manual Download

Page: 38 / 100

Chapter 2 Basic Operation

2. Stacking the Paper

2-1. Before stacking paper

Standard folding

There are six types of standard folding modes: single fold, double fold, irregular accordion fold (fold out),

letter fold, accordion fold (z fold) and gate fold. Paper is folded as shown below when the paper is placed on

the paper feed tray with its print side facing upward.

When paper is stacked with the gray surface on the obverse side and white surface on the reverse side on

the paper feed tray, and processing is completed in the standard folding mode, the folded paper is as shown

in the figure.

Paper feed direction

Ejection

direction

Single

fold

Double

fold

Irregular

accordion fold-out

Letter

fold

Accordion-

fold

Gate fold

2-2. Stacking paper

Do not put fingers inside during operation.

Keep away long hair, ties, jewelry and loose clothing.

It could cause injury.

Steps 1 and 6 are not necessary with the DF-999/DF-999A. Move on to steps 2 to 5.

Raise the paper set lever.

The paper feed stand will come down to the

paper stacking position when the paper set

lever is raised.

Loosen the guide fixing screw.

Summary of Contents for DF-990





































































































Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands

Duplo DF-990, Instruction Manual

Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands