DUNIWAY Stockroom Terranova 908A Instruction Manual Download Page 27

Page: 27 / 29

D U N I W A Y S T O C K R O O M C O R P .

27 of 29

VII

Return Procedure

If you need to return the gauge controller to Terranova for service:

-- Contact Duniway Stockroom to get a

RMA

(Return Material Authorization) number.

-- Then pack the instrument securely.

-- Use the original packaging if it is available.

-- If the Terranova 908A was shipped with a cable and/or CDG sensor, diagnosis and repair

will be more efficient if all components are returned together. If this is not convenient,

please consult with your Duniway Stockroom Customer Service Representative

-- If you do not have appropriate packing materials, a commercial packing and shipping

firm can provide them.

-- Be sure to mark the

RMA

number on the outside of the package.

TELEPHONE: 650-969-8811 TOLL-FREE (U.S. only): 800-446-8811 FAX: 650-965-0764 EMAIL: [email protected]

www.duniway.com

Summary of Contents for Terranova 908A






























Search results

Summary of Contents for Terranova 908A

Reviews:

Related manuals for Terranova 908A

Brands by name

Popular brands

DUNIWAY Stockroom Terranova 908A, Instruction Manual

Search results

Summary of Contents for Terranova 908A

Reviews:

Related manuals for Terranova 908A

Brands by name

Popular brands