background image

2

Introduction

Acquisition & Warranty

On delivery of your new Duncan SLR Feeder please check 
that the machine is not damaged. In cases of shipping 
damage, please ask your dealer to arrange for the appropriate 
claim to be lodged immediately. Assemble any parts supplied 
loose and inspect your machine with the aid of this manual to 
familiarise yourself with its features. If you have any queries 
ask your dealer straight away. The machine is covered by our 
12 month warranty on faulty parts, subject to normal use.

Record the serial number of your machine below and keep 
it in a secure place to help trace the machine and assist 
us when you order parts.

The Owner’s Manual

Your new Duncan SLR Feeder will give long and efficient 
service if given normal care and operated properly. 

This owner’s manual is provided so that you can become 
thoroughly familiar with the design of the machine and to 
furnish information on correct operation, adjustment and 
maintenance. 

Only persons well acquainted with these 

guidelines should be allowed to use the equipment.

A separate illustrated parts section has been provided so that 
if any parts are required your dealer will be able to supply 
them by reference to part numbers.

The manual is considered as part of your machine and must 
remain with the machine when it is sold.

Right and left hand references in this manual are 
determined by standing behind the machine and facing in 
the direction of travel

.

Model:

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Serial No:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Owner:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Delivery Date:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dealer:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

 

Disclaimer

  Every effort has been made to 
  ensure that the information in this 
  manual was accurate and up to 
  date at the time of going to press.  
  Clough Agriculture Ltd reserves the 
  right to make subsequent changes 
  to the machine, where necessary, 
  without notification.

  The Company will not be 
  responsible for any damage or 
  consequential loss arising out of 
  misinterpretation or failure to follow 
  recommended procedures. Nor will 
  it be liable for any damage caused 
  by or arising out of modification or 
  misuse of its product.

  The owner has a responsibility  
  to protect himself and others 
  by observing all safety
  information and by ensuring all  
  operators are well acquainted  
  with the safety information, 
  trained in the correct  use of  
  the machine and applying safe 
  work practices.

This Document contains the Original 
Operating Instructions for this machine 

and are verified by the Manufacturer.

Signed:......................................

Product Development Manager

Summary of Contents for SLR Feeder












































Reviews: