background image

Geelseweg, 80  |  2250  |  Olen  |   BELGIUM  |  Tel. +32 (0) 14 25 92 83  |  [email protected]  |  www.dumor.be

5

If they are correct then its a print shift issue as is the case 95% of the time.

Print shift issues

Symptom

1-   All the cards are equally too high  

Increase the first cut length 
Opposite if too low

2-  The image is creeping up the sheet the further down the sheet you go 

(remember the last card cut is at the top of the pile in the tray!!!

Increase the card length and / or the gutter cross cut length fractionally

3-  The image is creeping down the sheet the further down you go 

Decrease the card length and / or the gutter cross cut length fractionally

4-  The image moved constantly to one side 

Move the infeed side guides in the opposite direction

5-  The card spacing is too short 

Increase the gutter cut length

6-  The card spacing is too long 

Decrease the gutter cut length

7-  The image on the cards is skewed 

No adjustment possible => printer error

Tips to get a good result

-  The machine doesn’t need cut lines printed on the sheet to cut accurately!! 

Do not print them, they just get in the way ....

-  If you want to run the colour to the edge of the card do a 3 mm over print bleed so that if there is a minor print position error it will 

not be seen as a white edge.

Unjamming

Generally the paper will jam in the infeed side of the blade.
A message jammed will appear along with arrows.
Use the right arrow only to pull the paper back out.
If you use the left arrow the jam will get worse and the drive belt may snap 

(no warranty).

Copyright Dumor International 2106

A B C

A B C

A B C

A B C

Skew

Too high

Correct

Too low

Summary of Contents for EASYCARD A4+









Reviews: