background image

Engine does not start

1. Out of fuel

2. Engine oil low

3. Spark plug wire disconnected

from spark plug

4. Bad spark plug

5. Spark plug wire has shorted
6. Ignition inoperative

1. Fill fuel tank

2. Add engine oil

3. Connect spark plug wire

4. Replace spark plug

5. Contact service center

6. Contact service center

1. Stale fuel or water in fuel

2. Spark plug producing weak spark

3. Excessively rich fuel mixture

1. 

1. 

gasoline.

2. Contact service center
3. Contact service center

1. 

Engine hard to start

Engine lacks power and vibrates 

excessively

1. Out of fuel

1. Fill fuel tank

Engine quits during operation

PROBLEM

CAUSE

SOLUTION

1. Engine speed is too slow

1. Move throttle to fast. If this does

not correct problem, contact

service center.

Engine loses power when load is 

added

Water pressure is weak

1. Water supply is restricted.

2. Water not turned on to full power

3. Not using high pressure nozzle

1. Inspect garden hose for kinks or

leaks.  Make sure you are using

a large enough garden hose

(min. ¾ inch diameter)

2. Open water source all the way.

3. Change nozzle

TROUBLESHOOTING

Detergent and spray do not mix

1. Detergent hose is not submerged

or has disconnected

2. Black soap nozzle needed

1. Make sure hose is connected

2. Install soap nozzle

and submerged in the detergent.

Pump fails to produce pressure or 

pressure is inconsistent

1. Water supply is restricted

2. Water not turned on full power

3. Nozzle is clogged

4. Spray gun leaks

5. Air in line

6. Inlet hose screen is clogged

7. Water supply is over 100°F
8. Pump is faulty

1. Inspect garden hose for kinks or

leaks. Make sure you are using a

large enough garden hose (Min.

¾ inch diameter)

2. Open water source all the way.

3. Clean nozzle

4. Check spray gun connection or

replace spray gun

5. Squeeze trigger handle to

remove air

6. Clean inlet

7. Use cool water supply
8. Contact service center

2

0

Summary of Contents for DGPW3200






















Reviews: