background image

14

Always start the engine and let it stabilize before connecting any electronic devices.

Disconnect all electronic devices before stopping the engine.

WARNING!

Never start or stop engine with electrical devices plugged in to the receptacles.  Failure to

do so could damage the generator and / or connected electrical devices.

OPERATION

How to Stop Engine

Turn the ECO switch to the “OFF” position.

Disconnect any electronic device.  All loads

 MUST 

be disconnect from the generator.  Never start or stop the engine

with electrical devices plugged in to the receptacles.

Turn the 3 in 1 Start Switch to the “OFF” position.

Turn the Air Vent to the “OFF” position.

OFF

ON

CHOKE

How to Attach Electronic Devices

1. Before Starting generator

Make sure the generator is grounded (see page 10 for instructions).

Make sure the attached load is within the generator rated output  and the receptacle’s rated current.

Make sure all electrical cords and receptacles are in good condition.

Make sure all electronic devices are turned “OFF” before plugging them into the generator.

2. Start engine

3. If the attached load is small, turn the ECO switch to the “ON” position.  For a larger load, or if attaching multiple electronic   

devices turn the ECO switch to the “OFF” position.

4. Make sure the green AC pilot indicator light is on.

.

6. Allow generator output to stabilize (engine and attached devices run evenly) before plugging in the next load.

ON

OFF

节能

模式

关闭

开启

CH O K E

O N

O FF

Summary of Contents for D2000iS




























Reviews: