background image

12

13

TECHNICAL PARAMETERS

14kg

See the data plate on the base of the machine

W: 430 mm x H: 413 mm x D: 512 mm

560 slices per hour

CLEANING - DAILY

Before cleaning your Conveyor Toaster, tie hair back and ensure that you are wearing no loose 

clothing or jewellery. 

NEVER ALLOW A BUILD UP OF CRUMBS IN THE CRUMB 

TRAY AS THIS MAY CAUSE A FIRE. CLEAN DAILY.

STANDBY MODE

During periods of inactivity, you can use Standby Mode to reduce the power consumption of 

your appliance by up to 70%. When you are ready to go again, switch the control dial to either 

‘TOAST’ or ‘BAGEL’ and, in normal conditions, your machine will be ready to toast in just 2 

minutes; that’s a 50% time saving over Quick Start.
After 15 minutes on standby, your Conveyor Toaster will have used the same amount of 

energy as it would to get from room temperature to Quick Start temperature. As such, Dualit 

recommends switching the device off if you don’t intend to use it for longer than 15 minutes.

ANTI-TAMPER

Your Conveyor Toaster features a removable Anti-Tamper Guard. Note: Before setting up 

your Conveyor Toaster, ensure that you remove the legs and Anti-Tamper Guard from the 

polyfoam insert in the bottom of the box. For buffet environments, Dualit recommends fit

-

ting the Anti-Tamper Guard to avoid customers adjusting the Toast Settings Dial. The Guard 

should be fitted using M4 x 10.0mm screws and a Phillips head screwdriver. After selecting the 

correct toast settings, the Anti-Tamper Guard can be fitted as follows.

TOASTER STANDBY CHART

TEMPERATURE OF TOASTER

FULL TEMPERATURE

START STANDBY 

MODE

STANDBY TIME (15 MINS)

WARMING UP (15 MINS)

DURING THIS 

PERIOD THE 

TOASTING 

SETTING WILL 

NEED TO BE 

MONITORED 

AND REDUCED 

AS THE 

TOASTER 

WARMS UP

FULL TEMPERATURE- 

TOASTING 

STABILISED, NO 

NEED TO ADJUST 

TOASTING SETTING 

UNLESS BREAD 

TYPE OR USAGE 

CHANGES

TIME (APPROX.)

QUICK START 

(13 MINS)

1

1

REMOVE SCREWS

REMOVE CRUMB 
TRAY

LEFT SCREW

UNPLUG & COOL

2

2

RIGHT SCREW

WIPE

Insert and tighten the left-hand 

screw.

Unplug from mains, leave 

to cool for minimum 

of 1 hour, then wipe all 

external surfaces with a 

damp, non-abrasive cloth. 

Insert and tighten the       

right-hand screw. To remove, 

repeat in reverse order.

Remove Crumb Tray, tip out 

all of the crumbs, then clean 

with a damp cloth and replace. 

Ensure the area around the 

Conveyor Toaster is clean 

and crumb free. Clean the fan 

air intake with a damp, non-

abrasive cloth. 

 

3

3

Remove the two screws seen 

on the left and right-hand 

sides  of  the  controls.  Align  the                  

Anti-Tamper Guard with the 

screw holes. 

Remove the Crumb Tray. From 

a cold start, set the Conveyor 

Toaster to standby. Select toast 

setting 9. As the conveyor 

rotates, clean the exposed 

section of the belt. Wipe with 

a damp, non-abrasive cloth if 

lightly soiled or a dry, lightly 

abrasive pad if heavily soiled. 

Then wipe with a damp cloth.

Your toaster is fitted with a temperature limiting thermostat. During periods of inactivity, 

longer than 5 minutes, the elements will turn off (indicated by the red power indicator going 

off). Only introduce bread to the conveyor when the red light is on and the elements are 

glowing cherry red.

Summary of Contents for DCT2i










Reviews: