Document:
RE-TCC7 0B8
Document:
RE-TCC7 0B8
Update:
February 2008
Update:
February 2008
Page:
3
Page:
3
OWNER'S MANUAL
RE-TCC7 22X Zoom Camera
ZOOM WIDE / TELE - Drive from the zoom menu FOCUS - You set a value set manual
focus or autofocus is enabled (AUTO).
H / V Reverse
Here you can flip the image horizontally (H. REVERSE), MIRROR function, or in the vertical
direction (V. REVERSE).
title
E 'can type a description that will be shown in overlay
image
of the
camera.
By selecting UP / DOWN to select the position of the insertion in the upper or lower left.
Preset
There are 3 options
PRESET - Setting it to ON will ripristano the camera's factory settings
INITIAL - Setting it to OFF it is possible to inhibit the lens control
PHASE - Not used
Motion Detection
The camera allows you to report any changes in the image resulting from an intrusion. Upon the
occurrence of the intrusion
will appear
there
written MOTION
in
overlay for the whole duration of the alarm (enable the display in the OSD section)
ON / OFF - enables / disables the detection of the movement AREA - allows you to select
the area in which the detection is carried out. The image will appear divided into 64 boxes which
can be individually enabled or disabled in the survey.
TIME - indicates the alarm duration time 10/30/60 seconds
SENS - adjusts the detection sensitivity to avoid false alarms from small movements.
The zoom does not generate activation for motion detection alarm.
During the motion detection alarm can not be combined other alarm actions in addition to the
appearance of the MOTION written overlay
Position
ALARM - FREEZE Not used - Not used
POSITION
- IS'
possible
setting up
64
Preset zoom you can recall at will. It must indicate the preset number (1..64) and then set the
Zoom and Focus parameters.
NOTE:
The pre-placements are only called up from the setup menu, you can not set either, nor
NOTE:
The pre-placements are only called up from the setup menu, you can not set either, nor
recall the pre-positioning via the RS485 serial line, and it is not posssibile tie them to the Motion
Detection function. The pre-vegono placements used by the camera especially for the setting of
the zoom position to be taken up (see POWER ON)
Range
And 'possible to set two levels of gamma correction 0.45 (TYPE A) and 1.0 (TYPE B)
Power ON
Here there are the options to be performed when the camera.
BLUE BACK - ON Select to show a blue background during the entire process of the
camera start-up.
Leaving it to OFF will instantly be shown the actual shooting.
POSITION - E 'can set this parameter to ON, to make sure that the camera back to its
preferential zoom position after a power failure. It should indicate the position number (1 ... 64)
that you want, and that they will be set in the POSITION section. At every start the camera will
return to this position and not on vision at maximum wide angle factory. This feature is very
important if you are using the camera without remote control the zoom and you want it to be
always kept a certain zoom level even in case of blackouts.
Mask
This section serves to mask viewing zones, usually to protect privacy. E 'can set 4 mask areas
that you can associate with pleasure to
64 pre-placement. To the
call of
pre-
positioning will be automatically obscured the chosen area.
POSITION - Select the pre-positioning (1..64) to associate the masking. In general it is
enough to work on the Pre-positioning 1, which will leave the output of the active menu. It has
also carefully select the same preset 1 in the boot options (POWER ON), described in the
previous paragraph.
MASK - Choose the mask number (1..4) OFF / ON - Turn on or off the mask in the pre-set
position
H-Start / End-H / V-Start / V-End - Coordinates
that
delimit the mask area
CONNECT - This option should be enabled so that the masked area is maintained as such
even by operating the zoom manually. The mask will vary in size depending on to keep always
masked selected zoom level the area to be protected.
OSD (On Screen Display)
This section allows you to set options written over video
POSITION - Enable overlay in the pre-active position at that time video.
MOTION - MOTION Enable stamping written for the entire duration of a generated by the
motion detection alarm.
ZOOM - Enable superimpose ZOOM level
Zoom + AF
This is the default setup options Auto Focus (AF)
ZOOM + AF - ON / OFF enables or disables the automatic autofocus combined with the
zoom
AF SLEEP - Enabling this option autofocus stops working after 5 minutes image without
changes to resume only if there are significant changes of the recorded picture.
Language
Not used. Available only in English menu.
Comm ID
If you are using the camera control via RS485 serial line utilzzando a control console for a dome
camera or a VCR, is set
