Document:
RE-BCC8YK2 1C4
Document:
RE-BCC8YK2 1C4
Document:
RE-BCC8YK2 1C4
Page:
2
Page:
2
OWNER'S MANUAL
RE-BCC8YK2 camera license plate
DSE srl - Digital Surveillance Equipment - WWW.DSE.EU
framed. Recall that each lens has its own depth of field to which it is possible to put in focus in a
perfect way only a portion of the space in front of the camera. Concentrate on the most important
area where you will find the plate of the vehicle to adjust the focus optimally.
It may be helpful for an optimal adjustment to position a car stops at the exact point where it
carries out the reading of the license plate.
The lens adjustment ring nuts can be rotated only after having unscrewed the pawl. Retighten
after adjustment in order to avoid unwanted changes.
MODE 'DETECTION 1..6
The RE-BCC8YK2 camera is pre-programmed for the best performance in the detection of
plaques. They are preset 6 different types of adjustment can be selected according to the
shooting situation.
For each mode corresponds to a different speed of the electronic shutter of the camera Mode 1:
Mode 2 1/120: 1/250 Mode 3: Mode 4 1/500: 1/1000 Mode 5: Mode 6 1/2000: 1/4000
If the means transiting at a reduced speed, as in the case of access roads or gates you can
select the mode 2 or 3. It is necessary to choose one of the high shutter speed (3 or higher) if it
is expected that the means may be in transit even at high speed . A higher speed shutter image
to match against much darker. The choice of 1..6 mode must be done at night, with the
illuminators
IR lit
and after
adjusted
perfectly focusing lens as in the previous section. To change how
recovery move
mini joystick placed along the camera cable to the right and left. The number of the setting (1 to
6) will appear superimposed on the upper left in the image. Choose the setting that offers the
best performance under actual shooting conditions based on the estimated maximum speed of
the vehicles.
Note that in the night mode camera must shoot an image very dark and see only the license
plate is in a position of headlights that extinct.
IR LIGHT
The cameras integrates in its interior an infrared illuminator that emanates illumination invisible
to the human eye, but visible to the camera. The illuminator turns itself on when it gets dark and
the camera switches alone in night vision mode. The illuminator allows ignition
the vision of the license plate
total darkness
until its scope
lighting. In this camera, the illuminator is used for the vision of the automobile license plate and
not to allow the night vision of the medium or environment.
If this
is
request must be
the tiling of another camera.
IR threshold adjustment -
On the electronic circuit board inside the housing is placed a
IR threshold adjustment -
On the electronic circuit board inside the housing is placed a
IR threshold adjustment -
On the electronic circuit board inside the housing is placed a
potentiometer (see figure) to adjust the illuminator ignition threshold.
In most cases it is not necessary to adjust and recommend not to change the factory setting.
Intervening only if one realizes that the camera never switches to night mode or switches in
untimely manner due to abnormal conditions of ambient brightness. Turn clockwise for the
illuminator will light up later, unscrewing it anticlockwise will be activated soon. In the adjustment
keep in mind that the camera reaction occurs with 5 seconds delay to avoid that sudden flashes
can make the camera move from night to day. It is therefore necessary to turn a little
potentiometer and wait for the reaction of the camera.
IR brightness adjustment
- E 'can adjust the brightness of the illuminator to adapt to the distance
IR brightness adjustment
- E 'can adjust the brightness of the illuminator to adapt to the distance
of the shot. Of
rule this adjustment is not
necessary, but it can happen, especially in case of a short distance readings, which is necessary
to reduce the power of the LEDs to prevent the plaque appears bleached. To reduce the power of
the LED is necessary to act on the small joystick along the connection cable as shown in the
figure. Moving the joystick upward towards the camera by increasing the lighting, moving down
towards the connectors is reduced. Pressing the joystick will save the setting. Always remember
to confirm the setting of brightness control led by pressing the joystick to prevent the regulation is
changed in case of power failure. To properly adjust the lighting ask
in
real dark conditions and illuminators turned on by placing a retainer means in the license plate
reading point. then act on the regulation in order to optimize the illumination on the plate.
The brightness of the LED adjustment has no feedback in overlay in the image. E ', however,
possible to physically see the different power of brightness
RS485 FOR REMOTE CONTROL
The camera is equipped with an RS485 port that can be used to remotely control both the
detection modes 1 ... 6 of the camera is the brightness of the illuminators.
This remote connection is not essential for the operation but it can be useful because it allows to
adjust remotely the camera parameters to obtain the best yield strength without having to access
the camera itself.
And 'possible to send commands with the common protocol Pelco P / D using a control console
for our speed dome cameras or our DVR. The transmission speed of the protocol must be
9600bps.
On the inner sheet is placed a block with 8 switches to set the camera ID that the factory is: 1
They only use the swicth 1 to 5 which are used to assign the address to the camera according to
the following tables: