DSE DSE704 Operating Manual Download Page 13 | Manualshive

Page: 13 / 15

DSE DSE704 Operating Manual Download Page 13

057-042 704 Operating Instructions Issue 2.1 18/06/2007 11:27:00 JR - 13 -

5 SPECIFICATION

DC Supply: 8 Volts to 35 Volts DC Continuous.

Cranking Dropouts: Able to survive 0 Volts for 50 mS, providing supply was at

least 10 V before dropout and supply recovers to 5 Volts.
This is achieved without the need for internal batteries.

Max. Current: Operating 50mA

Standby 10mA

Alternator Input Range: 75 Volts (ph-N) to 277 Volts (ph-N) AC (+20%)

Mains Input Voltage 15 – 277 Volts (ph-N) AC (+20%)

Alternator Input Frequency: 50 - 60 Hz at rated engine speed

(Minimum: 75V AC Ph-N)
(Crank Disconnect from 15V Ph-N @ 20Hz)
Ove14% (+24% overshoot)
Underspeed –20%

Mains Frequency 50 – 60 Hz

Start Output: 1.2 Amp DC at supply voltage.

Fuel Output: 1.2 Amp DC at supply voltage.

Auxiliary Outputs: 1.2 Amp DC at supply voltage.

Dimensions: 125mm x 165mm x 28 mm

Charge Fail: 12 Volts = 8 Volts CF 24 Volts = 16 Volts CF

Operating Temperature Range: -30

°

C to + 70

0

C

Applicable Standards

Compliant with BS EN 60950 Low Voltage Directive
Compliant with BS EN 50081-2: 1992 EMC Directive
Compliant with BS EN 61000-6-4: 2000 EMC Directive

Compliance to European Legislation

Registered Component for USA & Canada

Deep Sea Electronics plc reserve the right to change specification without notice.

«
...
11
12
13
14
15
»

Summary of Contents for DSE704
















Reviews:

No comments