manualshive.com logo in svg

DSE DSE704, Operating Manual, Page: 12 / 15

Share
Download
DSE DSE704 Operating Manual Download Page 12

-  12 -     057-042 704 Operating Instructions Issue 2.1   18/06/2007 11:27:00  JR               
 

4   TERMINAL DESCRIPTION 

 

PIN 

No 

DESCRIPTION 

CABLE 

SIZE 

NOTES 

1 

DC Plant Supply Input  
(-ve) 

1.0mm 

Connected to plant battery negative 

2 

DC Plant Supply Input   
(+ve) 

1.0mm 

Connected to plant battery positive 
(Recommended Fuse 2A) 

3 

Fuel relay Output 

1.0mm 

Used to operate the fuel relay. 

4 

Start relay Output 

1.0mm 

Used to operate the cranking relay. 

5 

Auxiliary Output relay 1 

1.0mm 

Configurable output. 

6 

Auxiliary Output relay 2 

1.0mm 

Configurable output.  

7 

Charge Fail Input/ Excitation 
Output 

1.0mm 

Must NOT be connected to plant supply 
negative if not used. 

8 

Low Oil Pressure Input 

0.5mm 

Switch to negative. 

9 

High Engine Temp Input 

0.5mm 

Switch to negative. 

10 

Auxiliary Input 1 

0.5mm 

Switch to negative. 

11 

Auxiliary Input 2 

0.5mm 

Switch to negative. 

12 

Remote Start Input 

0.5mm 

Switch to negative. 

13 

Mains loading Relay 
Normally Open contact 

1.0mm 

Used to close the mains  
contactor / breaker 

14 

Generator loading Relay 
Normally Open contact 

1.0mm 

Used to close the generator  
contactor / breaker 

15 

Functional Earth 

1.0mm 

Connect to a good clean earth point 

16 

Mains L1  
Voltage Monitoring Input 

1.0mm 

Connect to Mains L1 supply (AC) 
(Recommend 2A Fuse Max.) 

17 

Mains L2  
Voltage Monitoring Input 

1.0mm 

Connect to Mains L1 supply (AC) 
(Recommend 2A Fuse Max.) 

18 

Mains L3  
Voltage Monitoring Input 

1.0mm 

Connect to Mains L1 supply (AC) 
(Recommend 2A Fuse Max.) 

19 

Mains N  
Voltage Monitoring Input 

1.0mm 

Connect to Mains N supply (AC) 

20 

Alternator Input L1 

1.0mm 

Do not connect if not used. (2A Fuse) 

21 

Alternator Input N 

1.0mm 

Do not connect if not used. 

 

NOTE:- 

For single phase mains monitoring the neutral should be connected to terminal 

19, L1 should be connected to terminals 16,17 and 18.

 

 

NOTE:- 

For two phase mains monitoring the L2 should be connected to terminal 19, L1 

should be connected to terminals 16,17 and 18. The voltage between the two phases must 
not exceed 305 Volts. 

 

NOTE:- All the outputs are solid state, rated at 1.2 Amps 8 Volts to 35 Volts DC, and 

switch to battery negative when active. 

 

Summary of Contents for DSE704
















Reviews:

No comments