background image

1 Introduction

1

1 Introduction

The Skyroute CL3050 is a standalone wireless communicator that sends alarm system infor-
mation to 

Connect 24

. Connect 24 then forwards this information to the central station. 

The Skyroute CL3050 automatically configures itself on power up to one of three opera-
tional modes or; if it is connected to a keypad, in the programming mode. The Skyroute 
CL3050 is pre programmed with the most commonly used settings for quick installation. If 
required the default options can be custom programmed.

Mode 1: Bell Follower 

If the Skyroute CL3050 does not detect a keypad or PC5108 expander card dur-
ing the first 15 seconds of power up, then mode 1 or 2 can be selected by press-
ing the enroll button. The red LED indicates Mode 1 and the yellow LED indicates 
mode 2. In Mode 1, the Skyroute CL3050 monitors the 

Bell Output

 of the con-

trol panel. The system identifies the Bell Output cadence and transmits the corre-
sponding Fire or Burglar alarm reporting code to 

Connect 24

.

Refer to the appropriate 

control panel Installation Manual.

Mode 2: 2-Zone

 

Panel

 

If Mode 2 is selected during power up the system will configure itself for 2 zone, 
stand alone operation with normally closed loops.

Mode 3: 8-Zone Panel

If the Skyroute CL3050 detects a PC5108 expander card on power up it will auto-
matically configure itself for 8-zone standalone operation with normally closed 
loops.

Programming Mode 

If the Skyroute CL3050 detects a keypad on power up it will go into the program-
ming mode. Programming mode allows the installer to custom program system 
options. Refer to Section 5, Programming Descriptions; and Section 6, Program-
ming Worksheets for programming options and default settings.

Note:

The only method of entering the Programming Mode is to power-down the unit, 
connect a PowerSeries keypad to the Keybus terminals, then reapply power to 
the Skyroute CL3050.

Figure 1

Summary of Contents for Skyroute CL3050





























Reviews: