NOTE:
In between displaying signal strength, the signal strength LEDs will flash alternately if an inactive SIM card is used. The
flashing indicates that the module is attempting to attach to the cellular network and will only last briefly.
Initial Panel Programming
Keypad Data Display
l
Section-Toggle Options:
The number is displayed when toggle is ON and the number is not displayed when toggle is
OFF. (e.g., toggle options displays: [--3--6--]. Options 3 and 6 are ON, all others are OFF). Pressing keys 1 through 8 will
alternately turn the toggle ON and OFF.
l
HEX/Decimal Data:
Values that are provided with two defaults, separated by a “/” character, use the format: hexadecimal
followed by decimal equivalent (e.g., default [0BF5/3061]). Hexadecimal numbers are shown, with all leading zeroes, to the
full field length defined for the number.
Entering HEX values at keypad
To enter HEX values at the keypad, press the * key before entering the HEX value. (e.g., to enter “C” at the keypad, press [*][3])
Entering ASCII Characters at keypad
1. Press [*] and use scroll buttons [<] [>] to display “ASCII Entry” on the LCD screen.
2. Press [*] to select ASCII entry mode.
3. Use the [<] [>] scroll keys to display the desired character and press [*] to save and exit ASCII.
4. Repeat the steps above to enter another ASCII character.
HS2016/2032/2064/2128 Initial Programming
For detailed information, refer to panel manual section ‘Alternate Communicator Set-up’. These sections must be programmed
at the panel keypad. Enter
[*][8][Installer Code] [Section Number]
. Record any values that are modified from their default, in
the appropriate worksheets for the panel or communicator.
1. In panel section
[377]
‘Communication Variables’, subsection
[002]
‘Communication Delays’, sub-subsection [1] ‘Com-
munication Delay’, program 060 (seconds).
2. In panel section
[382]
‘Communicator Option 3’ set option [5] ON
NOTE:
If this option is OFF, the yellow status LED on the communicator will indicate ‘Panel Supervision Trouble’ (2 flashes)
and the unit can not be programmed via the PC-LINK cable.
NOTE:
Account number in communicator section
[851][021]
automatically syncs with panel system account number in section
[310][000]
.
3. In panel sections
[300]
subsections
[001]
to
[004]
, program the subsection with 02 to 06
Table 5: Communicator Path Programming
Value
Communication Method
02
Auto Routing
03
Ethernet 1
04
Ethernet 2
05
Cellular 1
06
Cellular 2
NOTE:
Refer to panel manual for additional information
4. In panel section
[350]
‘Communication Formats’, program the communication format as: CID (03) or SIA FSK (04).
5. In panel sections
[311] - [318]
‘Partition Call Directions’, program the call direction options for the system.
6. In panel section
[401]
‘DLS/SA Options’, set toggle option [2] ‘User Enable DLS’ to ON in order to perform panel DLS
session through cellular or Ethernet.
NOTE:
Before leaving the premises, the installer should verify all programmed communications paths. See programming
options section
[851][901]
to send immediate test transmissions.
Communicator Troubles displayed on a HS2016/2032/2064/2128
The communication trouble is the only trouble that will appear on the keypad Liquid Crystal Display (LCD) when encountered
by a communicator installed in a HS2016/2032/2064/2128. For more information about the trouble on the communicator mod-
ule, refer to the panel event buffer or by accessing *2 to view the individual trouble types. Log entry will show Fault or Restore
for each of the following events:
l
Alt. comm SIM lock Trouble/Restore
l
Alt. comm Cellular Trouble/Restore
l
Alt. comm Ethernet Trouble/Restore
l
Alt. comm Fault/Restore
11
